@phdthesis{Pilz2010,
  author    = {Pilz, Marco},
  title     = {A comparison of proxies for seismic site conditions and amplification for the large urban area of Santiago de Chile},
  url       = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus-52961},
  school      = {Universit{\"a}t Potsdam},
  year      = {2010},
  abstract  = {Situated in an active tectonic region, Santiago de Chile, the country´s capital with more than six million inhabitants, faces tremendous earthquake hazard. Macroseismic data for the 1985 Valparaiso and the 2010 Maule events show large variations in the distribution of damage to buildings within short distances indicating strong influence of local sediments and the shape of the sediment-bedrock interface on ground motion. Therefore, a temporary seismic network was installed in the urban area for recording earthquake activity, and a study was carried out aiming to estimate site amplification derived from earthquake data and ambient noise. The analysis of earthquake data shows significant dependence on the local geological structure with regards to amplitude and duration. Moreover, the analysis of noise spectral ratios shows that they can provide a lower bound in amplitude for site amplification and, since no variability in terms of time and amplitude is observed, that it is possible to map the fundamental resonance frequency of the soil for a 26 km x 12 km area in the northern part of the Santiago de Chile basin. By inverting the noise spectral rations, local shear wave velocity profiles could be derived under the constraint of the thickness of the sedimentary cover which had previously been determined by gravimetric measurements. The resulting 3D model was derived by interpolation between the single shear wave velocity profiles and shows locally good agreement with the few existing velocity profile data, but allows the entire area, as well as deeper parts of the basin, to be represented in greater detail. The wealth of available data allowed further to check if any correlation between the shear wave velocity in the uppermost 30 m (vs30) and the slope of topography, a new technique recently proposed by Wald and Allen (2007), exists on a local scale. While one lithology might provide a greater scatter in the velocity values for the investigated area, almost no correlation between topographic gradient and calculated vs30 exists, whereas a better link is found between vs30 and the local geology. When comparing the vs30 distribution with the MSK intensities for the 1985 Valparaiso event it becomes clear that high intensities are found where the expected vs30 values are low and over a thick sedimentary cover. Although this evidence cannot be generalized for all possible earthquakes, it indicates the influence of site effects modifying the ground motion when earthquakes occur well outside of the Santiago basin. Using the attained knowledge on the basin characteristics, simulations of strong ground motion within the Santiago Metropolitan area were carried out by means of the spectral element technique. The simulation of a regional event, which has also been recorded by a dense network installed in the city of Santiago for recording aftershock activity following the 27 February 2010 Maule earthquake, shows that the model is capable to realistically calculate ground motion in terms of amplitude, duration, and frequency and, moreover, that the surface topography and the shape of the sediment bedrock interface strongly modify ground motion in the Santiago basin. An examination on the dependency of ground motion on the hypocenter location for a hypothetical event occurring along the active San Ram{\´o}n fault, which is crossing the eastern outskirts of the city, shows that the unfavorable interaction between fault rupture, radiation mechanism, and complex geological conditions in the near-field may give rise to large values of peak ground velocity and therefore considerably increase the level of seismic risk for Santiago de Chile.},
  language  = {en}
}
@phdthesis{Codutti2018,
  author    = {Codutti, Agnese},
  title     = {Behavior of magnetic microswimmers},
  doi       = {10.25932/publishup-42297},
  url       = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-422976},
  school      = {Universit{\"a}t Potsdam},
  pages     = {iv, 142},
  year      = {2018},
  abstract  = {Microswimmers, i.e. swimmers of micron size experiencing low Reynolds numbers, have received a great deal of attention in the last years, since many applications are envisioned in medicine and bioremediation. A promising field is the one of magnetic swimmers, since magnetism is biocom-patible and could be used to direct or actuate the swimmers. This thesis studies two examples of magnetic microswimmers from a physics point of view. The first system to be studied are magnetic cells, which can be magnetic biohybrids (a swimming cell coupled with a magnetic synthetic component) or magnetotactic bacteria (naturally occurring bacteria that produce an intracellular chain of magnetic crystals). A magnetic cell can passively interact with external magnetic fields, which can be used for direction. The aim of the thesis is to understand how magnetic cells couple this magnetic interaction to their swimming strategies, mainly how they combine it with chemotaxis (the ability to sense external gradient of chemical species and to bias their walk on these gradients). In particular, one open question addresses the advantage given by these magnetic interactions for the magnetotactic bacteria in a natural environment, such as porous sediments. In the thesis, a modified Active Brownian Particle model is used to perform simulations and to reproduce experimental data for different systems such as bacteria swimming in the bulk, in a capillary or in confined geometries. I will show that magnetic fields speed up chemotaxis under special conditions, depending on parameters such as their swimming strategy (run-and-tumble or run-and-reverse), aerotactic strategy (axial or polar), and magnetic fields (intensities and orientations), but it can also hinder bacterial chemotaxis depending on the system. The second example of magnetic microswimmer are rigid magnetic propellers such as helices or random-shaped propellers. These propellers are actuated and directed by an external rotating magnetic field. One open question is how shape and magnetic properties influence the propeller behavior; the goal of this research field is to design the best propeller for a given situation. The aim of the thesis is to propose a simulation method to reproduce the behavior of experimentally-realized propellers and to determine their magnetic properties. The hydrodynamic simulations are based on the use of the mobility matrix. As main result, I propose a method to match the experimental data, while showing that not only shape but also the magnetic properties influence the propellers swimming characteristics.},
  language  = {en}
}
@phdthesis{Moreira2001,
  author    = {Moreira, Andr{\´e} Gu{\´e}rin},
  title     = {Charged systems in bulk and at interfaces},
  url       = {http://nbn-resolving.de/urn:nbn:de:kobv:517-0000677},
  school      = {Universit{\"a}t Potsdam},
  year      = {2001},
  abstract  = {Eine der Faustregeln der Kolloid- und Oberfl{\"a}chenphysik ist, dass die meisten Oberfl{\"a}chen geladen sind, wenn sie mit einem L{\"o}sungsmittel, normalerweise Wasser, in Kontakt treten. Dies ist zum Beispiel bei ladungsstabilisierten Kolloidalen Suspensionen der Fall, bei denen die Oberfl{\"a}che der Kolloidteilchen geladen ist (gew{\"o}hnlich mit einer Ladung von mehreren Hunderttausend Elementarladungen), oder bei Monoschichten ionischer Tenside, die auf einer Luft-Wasser Grenzfl{\"a}che sitzen (wobei die wasserliebenden Kopfgruppen durch die Freisetzung von Gegenionen geladen werden), sowie bei Doppelschichten, die geladene phospholipide enthalten (wie Zellmembranen). In dieser Arbeit betrachten wir einige Modellsysteme, die zwar eine vereinfachte Fassung der Realit{\"a}t darstellen, von denen wir aber dennoch erwarten koennen, dass wir mit ihrer Hilfe einige physikalische Eigenschaften realer geladener Systeme (Kolloide und Elektrolyte) einfangen k{\"o}nnen.},
  language  = {en}
}
@phdthesis{Panzer2024,
  author    = {Panzer, Marcel},
  title     = {Design of a hyper-heuristics based control framework for modular production systems},
  doi       = {10.25932/publishup-63300},
  url       = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-633006},
  school      = {Universit{\"a}t Potsdam},
  pages     = {vi, 334},
  year      = {2024},
  abstract  = {Volatile supply and sales markets, coupled with increasing product individualization and complex production processes, present significant challenges for manufacturing companies. These must navigate and adapt to ever-shifting external and internal factors while ensuring robustness against process variabilities and unforeseen events. This has a pronounced impact on production control, which serves as the operational intersection between production planning and the shop- floor resources, and necessitates the capability to manage intricate process interdependencies effectively. Considering the increasing dynamics and product diversification, alongside the need to maintain constant production performances, the implementation of innovative control strategies becomes crucial. In recent years, the integration of Industry 4.0 technologies and machine learning methods has gained prominence in addressing emerging challenges in production applications. Within this context, this cumulative thesis analyzes deep learning based production systems based on five publications. Particular attention is paid to the applications of deep reinforcement learning, aiming to explore its potential in dynamic control contexts. Analysis reveal that deep reinforcement learning excels in various applications, especially in dynamic production control tasks. Its efficacy can be attributed to its interactive learning and real-time operational model. However, despite its evident utility, there are notable structural, organizational, and algorithmic gaps in the prevailing research. A predominant portion of deep reinforcement learning based approaches is limited to specific job shop scenarios and often overlooks the potential synergies in combined resources. Furthermore, it highlights the rare implementation of multi-agent systems and semi-heterarchical systems in practical settings. A notable gap remains in the integration of deep reinforcement learning into a hyper-heuristic. To bridge these research gaps, this thesis introduces a deep reinforcement learning based hyper- heuristic for the control of modular production systems, developed in accordance with the design science research methodology. Implemented within a semi-heterarchical multi-agent framework, this approach achieves a threefold reduction in control and optimisation complexity while ensuring high scalability, adaptability, and robustness of the system. In comparative benchmarks, this control methodology outperforms rule-based heuristics, reducing throughput times and tardiness, and effectively incorporates customer and order-centric metrics. The control artifact facilitates a rapid scenario generation, motivating for further research efforts and bridging the gap to real-world applications. The overarching goal is to foster a synergy between theoretical insights and practical solutions, thereby enriching scientific discourse and addressing current industrial challenges.},
  language  = {en}
}
@phdthesis{Konon2018,
  author    = {Konon, Alexander},
  title     = {Essays on career choice under risk and ambiguity},
  url       = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-416466},
  school      = {Universit{\"a}t Potsdam},
  pages     = {x, 250, xxxv},
  year      = {2018},
  abstract  = {This dissertation consists of five self-contained essays, addressing different aspects of career choices, especially the choice of entrepreneurship, under risk and ambiguity. In Chapter 2, the first essay develops an occupational choice model with boundedly rational agents, who lack information, receive noisy feedback, and are restricted in their decisions by their personality, to analyze and explain puzzling empirical evidence on entrepreneurial decision processes. In the second essay, in Chapter 3, I contribute to the literature on entrepreneurial choice by constructing a general career choice model on the basis of the assumption that outcomes are partially ambiguous. The third essay, in Chapter 4, theoretically and empirically analyzes the impact of media on career choices, where information on entrepreneurship provided by the media is treated as an informational shock affecting prior beliefs. The fourth essay, presented in Chapter 5, contains an empirical analysis of the effects of cyclical macro variables (GDP and unemployment) on innovative start-ups in Germany. In the fifth, and last, essay in Chapter 6, we examine whether information on personality is useful for advice, using the example of career advice.},
  language  = {en}
}
@phdthesis{Michalczyk2019,
  author    = {Michalczyk, Anna},
  title     = {Modelling of nitrogen cycles in intensive winter wheat-summer maize double cropping systems in the North China Plain},
  doi       = {10.25932/publishup-44421},
  url       = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-444213},
  school      = {Universit{\"a}t Potsdam},
  pages     = {X, 154},
  year      = {2019},
  abstract  = {The North China Plain (NCP) is one of the most productive and intensive agricultural regions in China. High doses of mineral nitrogen (N) fertiliser, often combined with flood irrigation, are applied, resulting in N surplus, groundwater depletion and environmental pollution. The objectives of this thesis were to use the HERMES model to simulate the N cycle in winter wheat (Triticum aestivum L.)-summer maize (Zea mays L.) double crop rotations and show the performance of the HERMES model, of the new ammonia volatilisation sub-module and of the new nitrification inhibition tool in the NCP. Further objectives were to assess the models potential to save N and water on plot and county scale, as well as on short and long-term. Additionally, improved management strategies with the help of a model-based nitrogen fertiliser recommendation (NFR) and adapted irrigation, should be found. Results showed that the HERMES model performed well under growing conditions of the NCP and was able to describe the relevant processes related to soil-plant interactions concerning N and water during a 2.5 year field experiment. No differences in grain yield between the real-time model-based NFR and the other treatments of the experiments on plot scale in Quzhou County could be found. Simulations with increasing amounts of irrigation resulted in significantly higher N leaching, higher N requirements of the NFR and reduced yields. Thus, conventional flood irrigation as currently practised by the farmers bears great uncertainties and exact irrigation amounts should be known for future simulation studies. In the best-practice scenario simulation on plot-scale, N input and N leaching, but also irrigation water could be reduced strongly within 2 years. Thus, the model-based NFR in combination with adapted irrigation had the highest potential to reduce nitrate leaching, compared to farmers practice and mineral N (Nmin)-reduced treatments. Also the calibrated and validated ammonia volatilisation sub-module of the HERMES model worked well under the climatic and soil conditions of northern China. Simple ammonia volatilisation approaches gave also satisfying results compared to process-oriented approaches. During the simulation with Ammonium sulphate Nitrate with nitrification inhibitor (ASNDMPP) ammonia volatilisation was higher than in the simulation without nitrification inhibitor, while the result for nitrate leaching was the opposite. Although nitrification worked well in the model, nitrification-born nitrous oxide emissions should be considered in future. Results of the simulated annual long-term (31 years) N losses in whole Quzhou County in Hebei Province were 296.8 kg N ha-1 under common farmers practice treatment and 101.7 kg N ha-1 under optimised treatment including NFR and automated irrigation (OPTai). Spatial differences in simulated N losses throughout Quzhou County, could only be found due to different N inputs. Simulations of an optimised treatment, could save on average more than 260 kg N ha-1a-1 from fertiliser input and 190 kg N ha-1a-1 from N losses and around 115.7 mm a-1 of water, compared to farmers practice. These long-term simulation results showed lower N and water saving potential, compared to short-term simulations and underline the necessity of long-term simulations to overcome the effect of high initial N stocks in soil. Additionally, the OPTai worked best on clay loam soil except for a high simulated denitrification loss, while the simulations using farmers practice irrigation could not match the actual water needs resulting in yield decline, especially for winter wheat. Thus, a precise adaption of management to actual weather conditions and plant growth needs is necessary for future simulations. However, the optimised treatments did not seem to be able to maintain the soil organic matter pools, even with full crop residue input. Extra organic inputs seem to be required to maintain soil quality in the optimised treatments. HERMES is a relatively simple model, with regard to data input requirements, to simulate the N cycle. It can offer interpretation of management options on plot, on county and regional scale for extension and research staff. Also in combination with other N and water saving methods the model promises to be a useful tool.},
  language  = {en}
}
@phdthesis{Schroeder2015,
  author    = {Schr{\"o}der, Sarah},
  title     = {Modelling surface evolution coupled with tectonics},
  url       = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-90385},
  school      = {Universit{\"a}t Potsdam},
  pages     = {viii, 129},
  year      = {2015},
  abstract  = {This study presents the development of 1D and 2D Surface Evolution Codes (SECs) and their coupling to any lithospheric-scale (thermo-)mechanical code with a quadrilateral structured surface mesh. Both SECs involve diffusion as approach for hillslope processes and the stream power law to reflect riverbed incision. The 1D SEC settles sediment that was produced by fluvial incision in the appropriate minimum, while the supply-limited 2D SEC DANSER uses a fast filling algorithm to model sedimantation. It is based on a cellular automaton. A slope-dependent factor in the sediment flux extends the diffusion equation to nonlinear diffusion. The discharge accumulation is achieved with the D8-algorithm and an improved drainage accumulation routine. Lateral incision enhances the incision's modelling. Following empirical laws, it incises channels of several cells width. The coupling method enables different temporal and spatial resolutions of the SEC and the thermo-mechanical code. It transfers vertical as well as horizontal displacements to the surface model. A weighted smoothing of the 3D surface displacements is implemented. The smoothed displacement vectors transmit the deformation by bilinear interpolation to the surface model. These interpolation methods ensure mass conservation in both directions and prevent the two surfaces from drifting apart. The presented applications refer to the evolution of the Pamir orogen. A calibration of DANSER's parameters with geomorphological data and a DEM as initial topography highlights the advantage of lateral incision. Preserving the channel width and reflecting incision peaks in narrow channels, this closes the huge gap between current orogen-scale incision models and observed topographies. River capturing models in a system of fault-bounded block rotations reaffirm the importance of the lateral incision routine for capturing events with channel initiation. The models show a low probability of river capturings with large deflection angles. While the probability of river capturing is directly depending on the uplift rate, the erodibility inside of a dip-slip fault speeds up headward erosion along the fault: The model's capturing speed increases within a fault. Coupling DANSER with the thermo-mechanical code SLIM 3D emphasizes the versatility of the SEC. While DANSER has minor influence on the lithospheric evolution of an indenter model, the brittle surface deformation is strongly affected by its sedimentation, widening a basin in between two forming orogens and also the southern part of the southern orogen to south, east and west.},
  language  = {en}
}
@phdthesis{Šustr2020,
  author    = {Šustr, David},
  title     = {Molecular diffusion in polyelectrolyte multilayers},
  doi       = {10.25932/publishup-48903},
  url       = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-489038},
  school      = {Universit{\"a}t Potsdam},
  pages     = {106},
  year      = {2020},
  abstract  = {Research on novel and advanced biomaterials is an indispensable step towards their applications in desirable fields such as tissue engineering, regenerative medicine, cell culture, or biotechnology. The work presented here focuses on such a promising material: polyelectrolyte multilayer (PEM) composed of hyaluronic acid (HA) and poly(L-lysine) (PLL). This gel-like polymer surface coating is able to accumulate (bio-)molecules such as proteins or drugs and release them in a controlled manner. It serves as a mimic of the extracellular matrix (ECM) in composition and intrinsic properties. These qualities make the HA/PLL multilayers a promising candidate for multiple bio-applications such as those mentioned above. The work presented aims at the development of a straightforward approach for assessment of multi-fractional diffusion in multilayers (first part) and at control of local molecular transport into or from the multilayers by laser light trigger (second part). The mechanism of the loading and release is governed by the interaction of bioactives with the multilayer constituents and by the diffusion phenomenon overall. The diffusion of a molecule in HA/PLL multilayers shows multiple fractions of different diffusion rate. Approaches, that are able to assess the mobility of molecules in such a complex system, are limited. This shortcoming motivated the design of a novel evaluation tool presented here. The tool employs a simulation-based approach for evaluation of the data acquired by fluorescence recovery after photobleaching (FRAP) method. In this approach, possible fluorescence recovery scenarios are primarily simulated and afterwards compared with the data acquired while optimizing parameters of a model until a sufficient match is achieved. Fluorescent latex particles of different sizes and fluorescein in an aqueous medium are utilized as test samples validating the analysis results. The diffusion of protein cytochrome c in HA/PLL multilayers is evaluated as well. This tool significantly broadens the possibilities of analysis of spatiotemporal FRAP data, which originate from multi-fractional diffusion, while striving to be widely applicable. This tool has the potential to elucidate the mechanisms of molecular transport and empower rational engineering of the drug release systems. The second part of the work focuses on the fabrication of such a spatiotemporarily-controlled drug release system employing the HA/PLL multilayer. This release system comprises different layers of various functionalities that together form a sandwich structure. The bottom layer, which serves as a reservoir, is formed by HA/PLL PEM deposited on a planar glass substrate. On top of the PEM, a layer of so-called hybrids is deposited. The hybrids consist of thermoresponsive poly(N-isopropylacrylamide) (PNIPAM) -based hydrogel microparticles with surface-attached gold nanorods. The layer of hybrids is intended to serve as a gate that controls the local molecular transport through the PEM-solution-interface. The possibility of stimulating the molecular transport by near-infrared (NIR) laser irradiation is being explored. From several tested approaches for the deposition of hybrids onto the PEM surface, the drying-based approach was identified as optimal. Experiments, that examine the functionality of the fabricated sandwich at elevated temperature, document the reversible volume phase transition of the PEM-attached hybrids while sustaining the sandwich stability. Further, the gold nanorods were shown to effectively absorb light radiation in the tissue- and cell-friendly NIR spectral region while transducing the energy of light into heat. The rapid and reversible shrinkage of the PEM-attached hybrids was thereby achieved. Finally, dextran was employed as a model transport molecule. It loads into the PEM reservoir in a few seconds with the partition constant of 2.4, while it spontaneously releases in a slower, sustained manner. The local laser irradiation of the sandwich, which contains the fluorescein isothiocyanate tagged dextran, leads to a gradual reduction of fluorescence intensity in the irradiated region. The release system fabricated employs renowned photoresponsivity of the hybrids in an innovative setting. The results of the research are a step towards a spatially-controlled on-demand drug release system that paves the way to spatiotemporally controlled drug release. The approaches developed in this work have the potential to elucidate the molecular dynamics in ECM and to foster engineering of multilayers with properties tuned to mimic the ECM. The work aims at spatiotemporal control over the diffusion of bioactives and their presentation to the cells.},
  language  = {en}
}
@phdthesis{Kieling2015,
  author    = {Kieling, Katrin},
  title     = {Quantification of ground motions by broadband simulations},
  url       = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-85989},
  school      = {Universit{\"a}t Potsdam},
  pages     = {XIV, 118},
  year      = {2015},
  abstract  = {In many procedures of seismic risk mitigation, ground motion simulations are needed to test systems or improve their effectiveness. For example they may be used to estimate the level of ground shaking caused by future earthquakes. Good physical models for ground motion simulation are also thought to be important for hazard assessment, as they could close gaps in the existing datasets. Since the observed ground motion in nature shows a certain variability, part of which cannot be explained by macroscopic parameters such as magnitude or position of an earthquake, it would be desirable that a good physical model is not only able to produce one single seismogram, but also to reveal this natural variability. In this thesis, I develop a method to model realistic ground motions in a way that is computationally simple to handle, permitting multiple scenario simulations. I focus on two aspects of ground motion modelling. First, I use deterministic wave propagation for the whole frequency range - from static deformation to approximately 10 Hz - but account for source variability by implementing self-similar slip distributions and rough fault interfaces. Second, I scale the source spectrum so that the modelled waveforms represent the correct radiated seismic energy. With this scaling I verify whether the energy magnitude is suitable as an explanatory variable, which characterises the amount of energy radiated at high frequencies - the advantage of the energy magnitude being that it can be deduced from observations, even in real-time. Applications of the developed method for the 2008 Wenchuan (China) earthquake, the 2003 Tokachi-Oki (Japan) earthquake and the 1994 Northridge (California, USA) earthquake show that the fine source discretisations combined with the small scale source variability ensure that high frequencies are satisfactorily introduced, justifying the deterministic wave propagation approach even at high frequencies. I demonstrate that the energy magnitude can be used to calibrate the high-frequency content in ground motion simulations. Because deterministic wave propagation is applied to the whole frequency range, the simulation method permits the quantification of the variability in ground motion due to parametric uncertainties in the source description. A large number of scenario simulations for an M=6 earthquake show that the roughness of the source as well as the distribution of fault dislocations have a minor effect on the simulated variability by diminishing directivity effects, while hypocenter location and rupture velocity more strongly influence the variability. The uncertainty in energy magnitude, however, leads to the largest differences of ground motion amplitude between different events, resulting in a variability which is larger than the one observed. For the presented approach, this dissertation shows (i) the verification of the computational correctness of the code, (ii) the ability to reproduce observed ground motions and (iii) the validation of the simulated ground motion variability. Those three steps are essential to evaluate the suitability of the method for means of seismic risk mitigation.},
  language  = {en}
}
@phdthesis{Uyaver2004,
  author    = {Uyaver, Sahin},
  title     = {Simulation of annealed polyelectrolytes in poor solvents},
  url       = {http://nbn-resolving.de/urn:nbn:de:kobv:517-0001488},
  school      = {Universit{\"a}t Potsdam},
  year      = {2004},
  abstract  = {Polymere sind lange kettenartige Molek{\"u}le. Sie bestehen aus vielen elementaren chemischen Einheiten, den Monomeren, die durch kovalente Bindungen aneinander gekettet sind. Polyelektrolyte sind Polymere, die ionisierbare Monomeren enthalten. Aufgrund ihrer speziellen Eigenschaften sind Polyelektrolyte sowohl in der Molekular- und Zellbiologie von großen Bedeutung als auch in der Chemie großtechnisch relevant. Verglichen mit ungeladenen Polymeren sind Polyelektrolyte theoretisch noch wenig verstanden. Insbesondere gilt dies f{\"u}r Polyelektrolyte in sogenanntem schlechten L{\"o}sungsmittel. Ein schlechtes L{\"o}sungsmittel bewirkt eine effektive Anziehung zwischen den Monomeren. F{\"u}r Polyelektrolyte in schlechtem L{\"o}sungsmittel kommt es daher zu einer Konkurrenz zwischen dieser Anziehung und der elektrostatischen Abstoßung. Geladene Polymere werden im Rahmen der chemischen Klassifikation in starke und schwache Polyelektrolyte unterschieden. Erstere zeigen vollst{\"a}ndige Dissoziation unabh{\"a}ngig vom pH-Wert der L{\"o}sung. Die Position der Ladungen auf der Kette wird ausschließlich w{\"a}hrend der Polymersynthese festgelegt. In der Physik spricht man deshalb von Polyelektrolyten mit eingefrorener Ladungsverteilung (quenched polyelectrolytes). Im Falle von schwachen Polyelektrolyten ist die Ladungsdichte auf der Kette nicht konstant, sondern wird durch der pH-Wert der L{\"o}sung kontrolliert. Durch Rekombinations- und Dissoziationsprozesse sind die Ladungen auf der Kette beweglich. Im allgemeinen stellt sich eine inhomogene Gleichgewichtsverteilung ein, die mit der Struktur der Kette gekoppelt ist. Diese Polymere werden deshalb auch Polyelektrolyte mit Gleichgewichtsladungsverteilung (annealed polyelectrolytes) genannt. Wegen des zus{\"a}tzlichen Freiheitsgrades in der Ladungsverteilung werden eine Reihe ungew{\"o}hnlicher Eigenschaften theoretisch vorhergesagt. Mit Hilfe von Simulationen ist es zum ersten Mal gelungen, zu zeigen daß 'annealed' Polyelektrolyte in relativ schlechtem L{\"o}sungsmittel einen diskontinuierlichen Phasen{\"u}bergang durchlaufen, wenn ein kritischer pH-Werts der L{\"o}sung {\"u}berschritten wird. Bei diesem Phasen{\"u}bergang, gehen die Polyelektolyte von einer schwach geladenen kompakten globul{\"a}ren Struktur zu einer stark geladenen gestreckten Konfiguration {\"u}ber. Aufgrund theoretischer Vorhersagen wird erwartet, daß die globul{\"a}re Struktur in weniger schlechtem L{\"o}sungsmittel instabil wird und sich eine Perlenkettenkonfiguration ausbildet. Diese Vorhersage konnte f{\"u}r 'annealed' Polyelektrolyte mit den durchgef{\"u}hrten Simulationen zum ersten Mal best{\"a}tigt werden - inzwischen auch durch erste experimentelle Ergebnisse. Schließlich zeigen die Simulationen auch, daß annealed Polyelektrolyte bei einer kritischen Salzkonzentration in der L{\"o}sung einen scharfen {\"U}bergang zwischen einem stark geladenen gestreckten Zustand und einem schwach geladenen globul{\"a}ren Zustand aufweisen, wiederum in {\"U}bereinstimmung mit theoretischen Erwartungen.},
  language  = {en}
}