@article{ShashevKupschLangeetal.2016, author = {Shashev, Yury and Kupsch, Andreas and Lange, Axel and M{\"u}ller, Bernd R. and Bruno, Giovanni}, title = {Improving the visibility of phase gratings for Talbot-Lau X-ray imaging}, series = {Materials testing : Materialpr{\~A}¼fung ; materials and components, technology and application}, volume = {58}, journal = {Materials testing : Materialpr{\~A}¼fung ; materials and components, technology and application}, publisher = {Hanser}, address = {M{\"u}nchen}, issn = {0025-5300}, doi = {10.3139/120.110948}, pages = {970 -- 974}, year = {2016}, abstract = {Talbot-Lau interferometry provides X-ray imaging techniques with significant enhancement of the radiographic contrast of weakly absorbing objects. The grating based technique allows separation of absorption, refraction and small angle scattering effects. The different efficiency of rectangular and triangular shaped phase gratings at varying detector distances is investigated. The interference patterns (Talbot carpets) are modeled for parallel monochromatic radiation and measured by synchrotron radiation. In comparison to rectangular shapes of phase gratings much higher visibility is obtained for triangular shapes which yield enhanced contrast of a glass capillary test specimen.}, language = {en} } @article{ShashevKupschLangeetal.2017, author = {Shashev, Yury and Kupsch, Andreas and Lange, Axel and Evsevleev, Sergei and M{\"u}ller, Bernd R. and Osenberg, Markus and Manke, Ingo and Hentschel, Manfred P. and Bruno, Giovanni}, title = {Optimizing the visibility of X-ray phase grating interferometry}, series = {Materials testing : Materialpr{\"u}fung ; materials and components, technology and application}, volume = {59}, journal = {Materials testing : Materialpr{\"u}fung ; materials and components, technology and application}, publisher = {Hanser}, address = {M{\"u}nchen}, issn = {0025-5300}, doi = {10.3139/120.111097}, pages = {974 -- 980}, year = {2017}, abstract = {The performance of grating interferometers coming up now for imaging interfaces within materials depends on the efficiency (visibility) of their main component, namely the phase grating. Therefore, experiments with monochromatic synchrotron radiation and corresponding simulations are carried out. The visibility of a phase grating is optimized by different photon energies, varying detector to grating distances and continuous rotation of the phase grating about the grid lines. Such kind of rotation changes the projected grating shapes, and thereby the distribution profiles of phase shifts. This yields higher visibilities than derived from ideal rectangular shapes. By continuous grating rotation and variation of the propagation distance, we achieve 2D visibility maps. Such maps provide the visibility for a certain combination of grating orientation and detector position. Optimum visibilities occur at considerably smaller distances than in the standard setup.}, language = {en} } @article{KupschMuellerLangeetal.2017, author = {Kupsch, Andreas and Mueller, Bernd R. and Lange, Axel and Bruno, Giovanni}, title = {Microstructure characterisation of ceramics via 2D and 3D X-ray refraction techniques}, series = {Journal of the European Ceramic Society}, volume = {37}, journal = {Journal of the European Ceramic Society}, publisher = {Elsevier}, address = {Oxford}, issn = {0955-2219}, doi = {10.1016/j.jeurceramsoc.2016.12.031}, pages = {1879 -- 1889}, year = {2017}, abstract = {3D imaging techniques are very fashionable nowadays, and allow enormous progress in understanding ceramic microstructure, its evolution, and its link to mechanical, thermal, and transport properties. In this feature article, we report the use of a powerful, yet not so wide-spread, set of X-ray techniques based on refraction effects. X-ray refraction allows determining internal specific surface (surface per unit volume) in a non-destructive fashion, position and orientation sensitive, and with a nanometric detectability. While the techniques are limited by the X-ray absorption of the material under investigation, we demonstrate showcases of ceramics and composite materials, where understanding of process parameter influence or simply of microstructural parameters could be achieved in a way unrivalled even by high-resolution techniques such as electron microscopy or computed tomography. (C) 2016 Elsevier Ltd. All rights reserved.}, language = {en} } @article{MishurovaCabezaArtztetal.2017, author = {Mishurova, Tatiana and Cabeza, Sandra and Artzt, Katia and Haubrich, Jan and Klaus, Manuela and Genzel, Christoph and Requena, Guillermo and Bruno, Giovanni}, title = {An Assessment of Subsurface Residual Stress Analysis in SLM Ti-6Al-4V}, series = {Materials}, volume = {10}, journal = {Materials}, publisher = {MDPI}, address = {Basel}, issn = {1996-1944}, doi = {10.3390/ma10040348}, pages = {14}, year = {2017}, abstract = {Ti-6Al-4V bridges were additively fabricated by selective laser melting (SLM) under different scanning speed conditions, to compare the effect of process energy density on the residual stress state. Subsurface lattice strain characterization was conducted by means of synchrotron diffraction in energy dispersive mode. High tensile strain gradients were found at the frontal surface for samples in an as-built condition. The geometry of the samples promotes increasing strains towards the pillar of the bridges. We observed that the higher the laser energy density during fabrication, the lower the lattice strains. A relief of lattice strains takes place after heat treatment.}, language = {en} } @article{BrunoVogel2017, author = {Bruno, Giovanni and Vogel, Sven C.}, title = {Simultaneous determination of high-temperature crystal structure and texture of synthetic porous cordierite}, series = {Journal of applied crystallography}, volume = {50}, journal = {Journal of applied crystallography}, publisher = {International Union of Crystallography}, address = {Chester}, issn = {1600-5767}, doi = {10.1107/S160057671700406X}, pages = {749 -- 762}, year = {2017}, abstract = {The evolution of the crystal structure and crystallographic texture of porous synthetic cordierite was studied by in situ high-temperature neutron diffraction up to 1373 K, providing the first in situ high-temperature texture measurement of this technologically important material. It was observed that the crystal texture slightly weakens with increasing temperature, concurrently with subtle changes in the crystal structure. These changes are in agreement with previous work, leading the authors to the conclusion that high-temperature neutron diffraction allows reliable crystallographic characterization of materials with moderate texture. It was also observed that structural changes occur at about the glass transition temperature of the cordierite glass (between 973 and 1073 K). Crystal structure refinements were conducted with and without quantitative texture analysis being part of the Rietveld refinement, and a critical comparison of the results is presented, contributing to the sparse body of literature on combined texture and crystal structure refinements.}, language = {en} } @article{CabezaMishurovaGarcesetal.2017, author = {Cabeza, Sandra and Mishurova, Tatiana and Garc{\´e}s, Gonzales and Sevostianov, Igor and Requena, Guillermo and Bruno, Giovanni}, title = {Stress-induced damage evolution in cast AlSi12CuMgNi alloy with one- and two-ceramic reinforcements}, series = {Journal of materials science}, volume = {52}, journal = {Journal of materials science}, publisher = {Springer}, address = {New York}, issn = {0022-2461}, doi = {10.1007/s10853-017-1182-7}, pages = {10198 -- 10216}, year = {2017}, abstract = {Two composites, consisting of an as-cast AlSi12CuMgNi alloy reinforced with 15 vol\% Al2O3 short fibres and with 7 vol\% Al2O3 short fibres + 15 vol\% SiC particles, were studied. Synchrotron computed tomography disclosed distribution, orientation, and volume fraction of the different phases. In-situ compression tests during neutron diffraction in direction parallel to the fibres plane revealed the load partition between phases. Internal damage (fragmentation) of the Si phase and Al2O3 fibres was directly observed in CT reconstructions. Significant debonding between Al matrix and SiC particles was also found. Finally, based on the Maxwell scheme, a micromechanical model was utilized for the new composite with two-ceramic reinforcements; it rationalizes the experimental data and predicts the evolution of all internal stress components in each phase.}, language = {en} } @article{NadammalCabezaMishurovaetal.2017, author = {Nadammal, Naresh and Cabeza, Sandra and Mishurova, Tatiana and Thiede, Tobias and Kromm, Arne and Seyfert, Christoph and Farahbod, Lena and Haberland, Christoph and Schneider, Judith Ann and Portella, Pedro Dolabella and Bruno, Giovanni}, title = {Effect of hatch length on the development of microstructure, texture and residual stresses in selective laser melted superalloy Inconel 718}, series = {Materials \& Design}, volume = {134}, journal = {Materials \& Design}, publisher = {Elsevier}, address = {Oxford}, issn = {0264-1275}, doi = {10.1016/j.matdes.2017.08.049}, pages = {139 -- 150}, year = {2017}, abstract = {In the present study, samples fabricated by varying the deposition hatch length during selective laser melting of nickel based superalloy Inconel 718 were investigated. Microstructure and texture of these samples was characterized using scanning electron microscopy, combined with electron back-scattered diffraction, and residual stress assessment, using neutron diffraction method. Textured columnar grains oriented along the sample building direction were observed in the shorter hatch length processed sample. A ten-fold increase in the hatch length reduced the texture intensity by a factor of two attributed to the formation of finer grains in the longer hatch length sample. Larger gradients of transverse residual stress in the longer hatch length sample were also observed. Along the build direction, compressive stresses in the shorter hatch length and negligible stresses for the longer hatch length specimen were observed. Changes to the temperature gradient (G) in response to the hatch length variation, influenced the G to growth rate (R) ratio and the product GxR, in agreement with the microstructures and textures formed. For the residual stress development, geometry of the part also played an important role. In summary, tailored isotropy could be induced in Inconel 718 by a careful selection of parameters during selective laser melting.}, language = {en} } @article{MuellerCooperLangeetal.2017, author = {M{\"u}ller, B. R. and Cooper, R. C. and Lange, A. and Kupsch, Andreas and Wheeler, M. and Hentschel, M. P. and Staude, A. and Pandey, A. and Shyam, A. and Bruno, Giovanni}, title = {Stress-induced microcrack density evolution in beta-eucryptite ceramics}, series = {Acta materialia}, volume = {144}, journal = {Acta materialia}, publisher = {Elsevier}, address = {Oxford}, issn = {1359-6454}, doi = {10.1016/j.actamat.2017.10.030}, pages = {627 -- 641}, year = {2017}, abstract = {In order to investigate their microcracking behaviour, the microstructures of several beta-eucryptite ceramics, obtained from glass precursor and cerammed to yield different grain sizes and microcrack densities, were characterized by laboratory and synchrotron x-ray refraction and tomography. Results were compared with those obtained from scanning electron microscopy (SEM). In SEM images, the characterized materials appeared fully dense but computed tomography showed the presence of pore clusters. Uniaxial tensile testing was performed on specimens while strain maps were recorded and analyzed by Digital Image Correlation (DIC). X-ray refraction techniques were applied on specimens before and after tensile testing to measure the amount of the internal specific surface (i.e., area per unit volume). X-ray refraction revealed that (a) the small grain size (SGS) material contained a large specific surface, originating from the grain boundaries and the interfaces of TiO2 precipitates; (b) the medium (MGS) and large grain size (LGS) materials possessed higher amounts of specific surface compared to SGS material due to microcracks, which decreased after tensile loading; (c) the precursor glass had negligible internal surface. The unexpected decrease in the internal surface of MGS and LGS after tensile testing is explained by the presence of compressive regions in the DIC strain maps and further by theoretical arguments. It is suggested that while some microcracks merge via propagation, more close mechanically, thereby explaining the observed X-ray refraction results. The mechanisms proposed would allow the development of a strain hardening route in ceramics.}, language = {en} } @article{CooperBrunoWheeleretal.2017, author = {Cooper, Ryan C. and Bruno, Giovanni and Wheeler, M. R. and Pandey, A. and Watkins, T. R. and Shyarn, A.}, title = {Effect of microcracking on the uniaxial tensile response of beta-eucryptite ceramics}, series = {Acta Materialia}, volume = {135}, journal = {Acta Materialia}, publisher = {Elsevier}, address = {Oxford}, issn = {1359-6454}, doi = {10.1016/j.actamat.2017.06.033}, pages = {361 -- 371}, year = {2017}, abstract = {A constitutive model for the nonlinear or "pseudoplastic" mechanical behavior in a linear-elastic solid with thermally induced microcracks is developed and applied to experimental results. The model is termed strain dependent microcrack density approximation (SDMDA) and is an extension of the modified differential scheme that describes the slope of the stress-strain curves of microcracked solids. SDMDA allows a continuous variation in the microcrack density with tensile loading. Experimental uniaxial tensile response of beta-eucryptite glass and ceramics with controlled levels of microcracking is reported. It is demonstrated that SDMDA can well describe the extent of non-linearity in the experimental uniaxial tensile response of beta-eucryptite with varying levels of microcracking. The advantages of the SDMDA are discussed in regard to tensile loading.}, language = {en} } @article{EvsevleevMishurovaCabezaetal.2018, author = {Evsevleev, Sergei and Mishurova, Tatiana and Cabeza, Sandra and Koos, R. and Sevostianov, Igor and Garc{\´e}s, Gonzales and Requena, Guillermo and Fernandez, R. and Bruno, Giovanni}, title = {The role of intermetallics in stress partitioning and damage evolution of AlSil2CuMgNi alloy}, series = {Materials Science and Engineering: A-Structural materials: properties, microstructure and processing}, volume = {736}, journal = {Materials Science and Engineering: A-Structural materials: properties, microstructure and processing}, publisher = {Elsevier}, address = {Lausanne}, issn = {0921-5093}, doi = {10.1016/j.msea.2018.08.070}, pages = {453 -- 464}, year = {2018}, abstract = {Load partitioning between phases in a cast AlSi12CuMgNi alloy was investigated by in-situ compression test during neutron diffraction experiments. Computed tomography (CT) was used to determine volume fractions of eutectic Si and intermetallic (IM) phases, and to assess internal damage after ex-situ compression tests. The CT reconstructed volumes showed the interconnectivity of IM phases, which build a 3D network together with eutectic Si. Large stresses were found in IMs, revealing their significant role as a reinforcement for the alloy. An existing micromechanical model based on Maxwell scheme was extended to the present case, assuming the alloy as a three-phase composite (Al matrix, eutectic Si, IM phases). The model agrees well with the experimental data. Moreover, it allows predicting the principal stresses in each phase, while experiments can only determine stress differences between the axial and radial sample directions. Finally, we showed that the addition of alloying elements not only allowed developing a 3D interconnected network, but also improved the strength of the Al matrix, and the ability of the alloy constituents to bear mechanical load.}, language = {en} }