@phdthesis{Pilz2010,
  author    = {Pilz, Marco},
  title     = {A comparison of proxies for seismic site conditions and amplification for the large urban area of Santiago de Chile},
  url       = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus-52961},
  school      = {Universit{\"a}t Potsdam},
  year      = {2010},
  abstract  = {Situated in an active tectonic region, Santiago de Chile, the country´s capital with more than six million inhabitants, faces tremendous earthquake hazard. Macroseismic data for the 1985 Valparaiso and the 2010 Maule events show large variations in the distribution of damage to buildings within short distances indicating strong influence of local sediments and the shape of the sediment-bedrock interface on ground motion. Therefore, a temporary seismic network was installed in the urban area for recording earthquake activity, and a study was carried out aiming to estimate site amplification derived from earthquake data and ambient noise. The analysis of earthquake data shows significant dependence on the local geological structure with regards to amplitude and duration. Moreover, the analysis of noise spectral ratios shows that they can provide a lower bound in amplitude for site amplification and, since no variability in terms of time and amplitude is observed, that it is possible to map the fundamental resonance frequency of the soil for a 26 km x 12 km area in the northern part of the Santiago de Chile basin. By inverting the noise spectral rations, local shear wave velocity profiles could be derived under the constraint of the thickness of the sedimentary cover which had previously been determined by gravimetric measurements. The resulting 3D model was derived by interpolation between the single shear wave velocity profiles and shows locally good agreement with the few existing velocity profile data, but allows the entire area, as well as deeper parts of the basin, to be represented in greater detail. The wealth of available data allowed further to check if any correlation between the shear wave velocity in the uppermost 30 m (vs30) and the slope of topography, a new technique recently proposed by Wald and Allen (2007), exists on a local scale. While one lithology might provide a greater scatter in the velocity values for the investigated area, almost no correlation between topographic gradient and calculated vs30 exists, whereas a better link is found between vs30 and the local geology. When comparing the vs30 distribution with the MSK intensities for the 1985 Valparaiso event it becomes clear that high intensities are found where the expected vs30 values are low and over a thick sedimentary cover. Although this evidence cannot be generalized for all possible earthquakes, it indicates the influence of site effects modifying the ground motion when earthquakes occur well outside of the Santiago basin. Using the attained knowledge on the basin characteristics, simulations of strong ground motion within the Santiago Metropolitan area were carried out by means of the spectral element technique. The simulation of a regional event, which has also been recorded by a dense network installed in the city of Santiago for recording aftershock activity following the 27 February 2010 Maule earthquake, shows that the model is capable to realistically calculate ground motion in terms of amplitude, duration, and frequency and, moreover, that the surface topography and the shape of the sediment bedrock interface strongly modify ground motion in the Santiago basin. An examination on the dependency of ground motion on the hypocenter location for a hypothetical event occurring along the active San Ram{\´o}n fault, which is crossing the eastern outskirts of the city, shows that the unfavorable interaction between fault rupture, radiation mechanism, and complex geological conditions in the near-field may give rise to large values of peak ground velocity and therefore considerably increase the level of seismic risk for Santiago de Chile.},
  language  = {en}
}
@phdthesis{Boeniger2010,
  author    = {B{\"o}niger, Urs},
  title     = {Attributes and their potential to analyze and interpret 3D GPR data},
  url       = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus-50124},
  school      = {Universit{\"a}t Potsdam},
  year      = {2010},
  abstract  = {Based on technological advances made within the past decades, ground-penetrating radar (GPR) has become a well-established, non-destructive subsurface imaging technique. Catalyzed by recent demands for high-resolution, near-surface imaging (e.g., the detection of unexploded ordnances and subsurface utilities, or hydrological investigations), the quality of today's GPR-based, near-surface images has significantly matured. At the same time, the analysis of oil and gas related reflection seismic data sets has experienced significant advances. Considering the sensitivity of attribute analysis with respect to data positioning in general, and multi-trace attributes in particular, trace positioning accuracy is of major importance for the success of attribute-based analysis flows. Therefore, to study the feasibility of GPR-based attribute analyses, I first developed and evaluated a real-time GPR surveying setup based on a modern tracking total station (TTS). The combination of current GPR systems capability of fusing global positioning system (GPS) and geophysical data in real-time, the ability of modern TTS systems to generate a GPS-like positional output and wireless data transmission using radio modems results in a flexible and robust surveying setup. To elaborate the feasibility of this setup, I studied the major limitations of such an approach: system cross-talk and data delays known as latencies. Experimental studies have shown that when a minimal distance of ~5 m between the GPR and the TTS system is considered, the signal-to-noise ratio of the acquired GPR data using radio communication equals the one without radio communication. To address the limitations imposed by system latencies, inherent to all real-time data fusion approaches, I developed a novel correction (calibration) strategy to assess the gross system latency and to correct for it. This resulted in the centimeter trace accuracy required by high-frequency and/or three-dimensional (3D) GPR surveys. Having introduced this flexible high-precision surveying setup, I successfully demonstrated the application of attribute-based processing to GPR specific problems, which may differ significantly from the geological ones typically addressed by the oil and gas industry using seismic data. In this thesis, I concentrated on archaeological and subsurface utility problems, as they represent typical near-surface geophysical targets. Enhancing 3D archaeological GPR data sets using a dip-steered filtering approach, followed by calculation of coherency and similarity, allowed me to conduct subsurface interpretations far beyond those obtained by classical time-slice analyses. I could show that the incorporation of additional data sets (magnetic and topographic) and attributes derived from these data sets can further improve the interpretation. In a case study, such an approach revealed the complementary nature of the individual data sets and, for example, allowed conclusions about the source location of magnetic anomalies by concurrently analyzing GPR time/depth slices to be made. In addition to archaeological targets, subsurface utility detection and characterization is a steadily growing field of application for GPR. I developed a novel attribute called depolarization. Incorporation of geometrical and physical feature characteristics into the depolarization attribute allowed me to display the observed polarization phenomena efficiently. Geometrical enhancement makes use of an improved symmetry extraction algorithm based on Laplacian high-boosting, followed by a phase-based symmetry calculation using a two-dimensional (2D) log-Gabor filterbank decomposition of the data volume. To extract the physical information from the dual-component data set, I employed a sliding-window principle component analysis. The combination of the geometrically derived feature angle and the physically derived polarization angle allowed me to enhance the polarization characteristics of subsurface features. Ground-truth information obtained by excavations confirmed this interpretation. In the future, inclusion of cross-polarized antennae configurations into the processing scheme may further improve the quality of the depolarization attribute. In addition to polarization phenomena, the time-dependent frequency evolution of GPR signals might hold further information on the subsurface architecture and/or material properties. High-resolution, sparsity promoting decomposition approaches have recently had a significant impact on the image and signal processing community. In this thesis, I introduced a modified tree-based matching pursuit approach. Based on different synthetic examples, I showed that the modified tree-based pursuit approach clearly outperforms other commonly used time-frequency decomposition approaches with respect to both time and frequency resolutions. Apart from the investigation of tuning effects in GPR data, I also demonstrated the potential of high-resolution sparse decompositions for advanced data processing. Frequency modulation of individual atoms themselves allows to efficiently correct frequency attenuation effects and improve resolution based on shifting the average frequency level. GPR-based attribute analysis is still in its infancy. Considering the growing widespread realization of 3D GPR studies there will certainly be an increasing demand towards improved subsurface interpretations in the future. Similar to the assessment of quantitative reservoir properties through the combination of 3D seismic attribute volumes with sparse well-log information, parameter estimation in a combined manner represents another step in emphasizing the potential of attribute-driven GPR data analyses.},
  language  = {en}
}
@phdthesis{Scherler2010,
  author    = {Scherler, Dirk},
  title     = {Climate variability and glacial dynamics in the Himalaya},
  url       = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus-49871},
  school      = {Universit{\"a}t Potsdam},
  year      = {2010},
  abstract  = {In den Hochgebirgen Asiens bedecken Gletscher eine Fl{\"a}che von ungef{\"a}hr 115,000 km² und ergeben damit, neben Gr{\"o}nland und der Antarktis, eine der gr{\"o}ßten Eisakkumulationen der Erde. Die Sensibilit{\"a}t der Gletscher gegen{\"u}ber Klimaschwankungen macht sie zu wertvollen pal{\"a}oklimatischen Archiven in Hochgebirgen, aber gleichzeitig auch anf{\"a}llig gegen{\"u}ber rezenter und zuk{\"u}nftiger globaler Erw{\"a}rmung. Dies kann vor allem in dicht besiedelten Gebieten S{\"u}d-, Ost- und Zentralasiens zu großen Problem f{\"u}hren, in denen Gletscher- und Schnee-Schmelzw{\"a}sser eine wichtige Ressource f{\"u}r Landwirtschaft und Stromerzeugung darstellen. Eine erfolgreiche Prognose des Gletscherverhaltens in Reaktion auf den Klimawandel und die Minderung der sozio{\"o}konomischen Auswirkungen erfordert fundierte Kenntnisse der klimatischen Steuerungsfaktoren und der Dynamik asiatischer Gletscher. Aufgrund ihrer Abgeschiedenheit und dem erschwerten Zugang gibt es nur wenige glaziologische Gel{\"a}ndestudien, die zudem r{\"a}umlich und zeitlich sehr begrenzt sind. Daher fehlen bisher grundlegende Informationen {\"u}ber die Mehrzahl asiatischer Gletscher. In dieser Arbeit benutze ich verschiedene Methoden, um die Dynamik asiatischer Gletscher auf mehreren Zeitskalen zu untersuchen. Erstens teste ich eine Methode zur pr{\"a}zisen satelliten-gest{\"u}tzten Messung von Gletscheroberfl{\"a}chen-Geschwindigkeiten. Darauf aufbauend habe ich eine umfassende regionale Erhebung der Fliessgeschwindigkeiten und Frontdynamik asiatischer Gletscher f{\"u}r die Jahre 2000 bis 2008 durchgef{\"u}hrt. Der gewonnene Datensatz erlaubt einmalige Einblicke in die topographischen und klimatischen Steuerungsfaktoren der Gletscherfließgeschwindigkeiten in den Gebirgsregionen Hochasiens. Insbesondere dokumentieren die Daten rezent ungleiches Verhalten der Gletscher im Karakorum und im Himalaja, welches ich auf die konkurrierenden klimatischen Einfl{\"u}sse der Westwinddrift im Winter und des Indischen Monsuns im Sommer zur{\"u}ckf{\"u}hre. Zweitens untersuche ich, ob klimatisch bedingte Ost-West Unterschiede im Gletscherverhalten auch auf l{\"a}ngeren Zeitskalen eine Rolle spielen und gegebenenfalls f{\"u}r dokumentierte regional asynchrone Gletschervorst{\"o}ße relevant sind. Dazu habe ich mittels kosmogener Nuklide Oberfl{\"a}chenalter von erratischen Bl{\"o}cken auf Mor{\"a}nen ermittelt und eine glaziale Chronologie f{\"u}r das obere Tons Tal, in den Quellgebieten des Ganges, erstellt. Dieses Gebiet befindet sich in der {\"U}bergangszone von monsunaler zu Westwind beeinflusster Feuchtigkeitszufuhr und ist damit ideal gelegen, um die Auswirkungen dieser beiden atmosph{\"a}rischen Zirkulationssysteme auf Gletschervorst{\"o}ße zu untersuchen. Die ermittelte glaziale Chronologie dokumentiert mehrere Gletscherschwankungen w{\"a}hrend des Endstadiums der letzten Pleistoz{\"a}nen Vereisung und w{\"a}hrend des Holz{\"a}ns. Diese weisen darauf hin, dass Gletscherschwankungen im westlichen Himalaja weitestgehend synchron waren und auf graduelle glaziale-interglaziale Temperaturver{\"a}nderungen, {\"u}berlagert von monsunalen Niederschlagsschwankungen h{\"o}herer Frequenz, zur{\"u}ck zu f{\"u}hren sind. In einem dritten Schritt kombiniere ich Satelliten-Klimadaten mit Eisfluss-Absch{\"a}tzungen und topographischen Analysen, um den Einfluss der Gletscher Hochasiens auf die Reliefentwicklung im Hochgebirge zu untersuchen. Die Ergebnisse dokumentieren ausgepr{\"a}gte meridionale Unterschiede im Grad und im Stil der Vergletscherung und glazialen Erosion in Abh{\"a}ngigkeit von topographischen und klimatischen Faktoren. Gegens{\"a}tzlich zu bisherigen Annahmen deuten die Daten darauf hin, dass das monsunale Klima im zentralen Himalaja die glaziale Erosion schw{\"a}cht und durch den Erhalt einer steilen orographischen Barriere das Tibet Plateau vor lateraler Zerschneidung bewahrt. Die Ergebnisse dieser Arbeit dokumentieren, wie klimatische und topographische Gradienten die Gletscherdynamik in den Hochgebirgen Asiens auf Zeitskalen von 10^0 bis 10^6 Jahren beeinflussen. Die Reaktionszeit der Gletscher auf Klimaver{\"a}nderungen sind eng an Eigenschaften wie Schuttbedeckung und Neigung gekoppelt, welche ihrerseits von den topographischen Verh{\"a}ltnissen bedingt sind. Derartige Einflussfaktoren m{\"u}ssen bei pal{\"a}oklimatischen Rekonstruktion und Vorhersagen {\"u}ber die Entwicklung asiatischer Gletscher ber{\"u}cksichtigt werden. Desweiteren gehen die regionalen topographischen Unterschiede der vergletscherten Gebiete Asiens teilweise auf klimatische Gradienten und den langfristigen Einfluss der Gletscher auf die topographische Entwicklung des Gebirgssystems zur{\"u}ck.},
  language  = {en}
}
@phdthesis{Shirzaei2010,
  author    = {Shirzaei, Manoochehr},
  title     = {Crustal deformation source monitoring using advanced InSAR time series and time dependent inverse modeling},
  url       = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus-50774},
  school      = {Universit{\"a}t Potsdam},
  year      = {2010},
  abstract  = {Crustal deformation can be the result of volcanic and tectonic activity such as fault dislocation and magma intrusion. The crustal deformation may precede and/or succeed the earthquake occurrence and eruption. Mitigating the associated hazard, continuous monitoring of the crustal deformation accordingly has become an important task for geo-observatories and fast response systems. Due to highly non-linear behavior of the crustal deformation fields in time and space, which are not always measurable using conventional geodetic methods (e.g., Leveling), innovative techniques of monitoring and analysis are required. In this thesis I describe novel methods to improve the ability for precise and accurate mapping the spatiotemporal surface deformation field using multi acquisitions of satellite radar data. Furthermore, to better understand the source of such spatiotemporal deformation fields, I present novel static and time dependent model inversion approaches. Almost any interferograms include areas where the signal decorrelates and is distorted by atmospheric delay. In this thesis I detail new analysis methods to reduce the limitations of conventional InSAR, by combining the benefits of advanced InSAR methods such as the permanent scatterer InSAR (PSI) and the small baseline subsets (SBAS) with a wavelet based data filtering scheme. This novel InSAR time series methodology is applied, for instance, to monitor the non-linear deformation processes at Hawaii Island. The radar phase change at Hawaii is found to be due to intrusions, eruptions, earthquakes and flank movement processes and superimposed by significant environmental artifacts (e.g., atmospheric). The deformation field, I obtained using the new InSAR analysis method, is in good agreement with continuous GPS data. This provides an accurate spatiotemporal deformation field at Hawaii, which allows time dependent source modeling. Conventional source modeling methods usually deal with static deformation field, while retrieving the dynamics of the source requires more sophisticated time dependent optimization approaches. This problem I address by combining Monte Carlo based optimization approaches with a Kalman Filter, which provides the model parameters of the deformation source consistent in time. I found there are numerous deformation sources at Hawaii Island which are spatiotemporally interacting, such as volcano inflation is associated to changes in the rifting behavior, and temporally linked to silent earthquakes. I applied these new methods to other tectonic and volcanic terrains, most of which revealing the importance of associated or coupled deformation sources. The findings are 1) the relation between deep and shallow hydrothermal and magmatic sources underneath the Campi Flegrei volcano, 2) gravity-driven deformation at Damavand volcano, 3) fault interaction associated with the 2010 Haiti earthquake, 4) independent block wise flank motion at the Hilina Fault system, Kilauea, and 5) interaction between salt diapir and the 2005 Qeshm earthquake in southern Iran. This thesis, written in cumulative form including 9 manuscripts published or under review in peer reviewed journals, improves the techniques for InSAR time series analysis and source modeling and shows the mutual dependence between adjacent deformation sources. These findings allow more realistic estimation of the hazard associated with complex volcanic and tectonic systems.},
  language  = {en}
}
@phdthesis{DiGiacomo2010,
  author    = {Di Giacomo, Domenico},
  title     = {Determination of the energy magnitude ME : application to rapid response purposes and insights to regional/local variabilities},
  url       = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus-50768},
  school      = {Universit{\"a}t Potsdam},
  year      = {2010},
  abstract  = {Recent large earthquakes put in evidence the need of improving and developing robust and rapid procedures to properly calculate the magnitude of an earthquake in a short time after its occurrence. The most famous example is the 26 December 2004 Sumatra earthquake, when the limitations of the standard procedures adopted at that time by many agencies failed to provide accurate magnitude estimates of this exceptional event in time to launch early enough warnings and appropriate response. Being related to the radiated seismic energy ES, the energy magnitude ME is a good estimator of the high frequency content radiated by the source which goes into the seismic waves. However, a procedure to rapidly determine ME (that is to say, within 15 minutes after the earthquake occurrence) was required. Here it is presented a procedure able to provide in a rapid way the energy magnitude ME for shallow earthquakes by analyzing teleseismic P‑waves in the distance range 20-98. To account for the energy loss experienced by the seismic waves from the source to the receivers, spectral amplitude decay functions obtained from numerical simulations of Greens functions based on the average global model AK135Q are used. The proposed method has been tested using a large global dataset (~1000 earthquakes) and the obtained rapid ME estimations have been compared to other magnitude scales from different agencies. Special emphasis is given to the comparison with the moment magnitude MW, since the latter is very popular and extensively used in common seismological practice. However, it is shown that MW alone provide only limited information about the seismic source properties, and that disaster management organizations would benefit from a combined use of MW and ME in the prompt evaluation of an earthquake's tsunami and shaking potential. In addition, since the proposed approach for ME is intended to work without knowledge of the fault plane geometry (often available only hours after an earthquake occurrence), the suitability of this method is discussed by grouping the analyzed earthquakes according to their type of mechanism (strike-slip, normal faulting, thrust faulting, etc.). No clear trend is found from the rapid ME estimates with the different fault plane solution groups. This is not the case for the ME routinely determined by the U.S. Geological Survey, which uses specific radiation pattern corrections. Further studies are needed to verify the effect of such corrections on ME estimates. Finally, exploiting the redundancy of the information provided by the analyzed dataset, the components of variance on the single station ME estimates are investigated. The largest component of variance is due to the intra-station (record-to-record) error, although the inter-station (station-to-station) error is not negligible and is of several magnitude units for some stations. Moreover, it is shown that the intra-station component of error is not random but depends on the travel path from a source area to a given station. Consequently, empirical corrections may be used to account for the heterogeneities of the real Earth not considered in the theoretical calculations of the spectral amplitude decay functions used to correct the recorded data for the propagation effects.},
  language  = {en}
}
@phdthesis{Strollo2010,
  author    = {Strollo, Angelo},
  title     = {Development of techniques for earthquake microzonation studies in different urban environment},
  url       = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus-53807},
  school      = {Universit{\"a}t Potsdam},
  year      = {2010},
  abstract  = {The proliferation of megacities in many developing countries, and their location in areas where they are exposed to a high risk from large earthquakes, coupled with a lack of preparation, demonstrates the requirement for improved capabilities in hazard assessment, as well as the rapid adjustment and development of land-use planning. In particular, within the context of seismic hazard assessment, the evaluation of local site effects and their influence on the spatial distribution of ground shaking generated by an earthquake plays an important role. It follows that the carrying out of earthquake microzonation studies, which aim at identify areas within the urban environment that are expected to respond in a similar way to a seismic event, are essential to the reliable risk assessment of large urban areas. Considering the rate at which many large towns in developing countries that are prone to large earthquakes are growing, their seismic microzonation has become mandatory. Such activities are challenging and techniques suitable for identifying site effects within such contexts are needed. In this dissertation, I develop techniques for investigating large-scale urban environments that aim at being non-invasive, cost-effective and quickly deployable. These peculiarities allow one to investigate large areas over a relative short time frame, with a spatial sampling resolution sufficient to provide reliable microzonation. Although there is a negative trade-off between the completeness of available information and extent of the investigated area, I attempt to mitigate this limitation by combining two, what I term layers, of information: in the first layer, the site effects at a few calibration points are well constrained by analyzing earthquake data or using other geophysical information (e.g., shear-wave velocity profiles); in the second layer, the site effects over a larger areal coverage are estimated by means of single-station noise measurements. The microzonation is performed in terms of problem-dependent quantities, by considering a proxy suitable to link information from the first layer to the second one. In order to define the microzonation approach proposed in this work, different methods for estimating site effects have been combined and tested in Potenza (Italy), where a considerable amount of data was available. In particular, the horizontal-to-vertical spectral ratio computed for seismic noise recorded at different sites has been used as a proxy to combine the two levels of information together and to create a microzonation map in terms of spectral intensity ratio (SIR). In the next step, I applied this two-layer approach to Istanbul (Turkey) and Bishkek (Kyrgyzstan). A similar hybrid approach, i.e., combining earthquake and noise data, has been used for the microzonation of these two different urban environments. For both cities, after having calibrated the fundamental frequencies of resonance estimated from seismic noise with those obtained by analysing earthquakes (first layer), a fundamental frequency map has been computed using the noise measurements carried out within the town (second layer). By applying this new approach, maps of the fundamental frequency of resonance for Istanbul and Bishkek have been published for the first time. In parallel, a microzonation map in terms of SIR has been incorporated into a risk scenario for the Potenza test site by means of a dedicated regression between spectral intensity (SI) and macroseismic intensity (EMS). The scenario study confirms the importance of site effects within the risk chain. In fact, their introduction into the scenario led to an increase of about 50\% in estimates of the number of buildings that would be partially or totally collapsed. Last, but not least, considering that the approach developed and applied in this work is based on measurements of seismic noise, their reliability has been assessed. A theoretical model describing the self-noise curves of different instruments usually adopted in microzonation studies (e.g., those used in Potenza, Istanbul and Bishkek) have been considered and compared with empirical data recorded in Cologne (Germany) and Gubbio (Italy). The results show that, depending on the geological and environmental conditions, the instrumental noise could severely bias the results obtained by recording and analysing ambient noise. Therefore, in this work I also provide some guidelines for measuring seismic noise.},
  language  = {en}
}
@phdthesis{Landgraf2010,
  author    = {Landgraf, Angela},
  title     = {Fault interaction at different time- and length scales : the North Tehran thrust and Mosha-Fasham fault (Alborz mountains, Iran)},
  url       = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus-50800},
  school      = {Universit{\"a}t Potsdam},
  year      = {2010},
  abstract  = {The seismically active Alborz mountains of northern Iran are an integral part of the Arabia-Eurasia collision. Linked strike-slip and thrust/reverse-fault systems in this mountain belt are characterized by slow loading rates, and large earthquakes are highly disparate in space and time. Similar to other intracontinental deformation zones such a pattern of tectonic activity is still insufficiently understood, because recurrence intervals between seismic events may be on the order of thousands of years, and are thus beyond the resolution of short term measurements based on GPS or instrumentally recorded seismicity. This study bridges the gap of deformation processes on different time scales. In particular, my investigation focuses on deformation on the Quaternary time scale, beyond present-day deformation rates, and it uses present-day and paleotectonic characteristics to model fault behavior. The study includes data based on structural and geomorphic mapping, faultkinematic analysis, DEM-based morphometry, and numerical fault-interaction modeling. In order to better understand the long- to short term behavior of such complex fault systems, I used geomorphic surfaces as strain markers and dated fluvial and alluvial surfaces using terrestrial cosmogenic nuclides (TCN, 10Be, 26Al, 36Cl) and optically stimulated luminescence (OSL). My investigation focuses on the seismically active Mosha-Fasham fault (MFF) and the seismically virtually inactive North Tehran Thrust (NTT), adjacent to the Tehran metropolitan area. Fault-kinematic data reveal an early mechanical linkage of the NTT and MFF during an earlier dextral transpressional stage, when the shortening direction was oriented northwest. This regime was superseded by Pliocene to Recent NE-oriented shortening, which caused thrusting and sinistral strike-slip faulting. In the course of this kinematic changeover, the NTT and MFF were reactivated and incorporated into a nascent transpressional duplex, which has significantly affected landscape evolution in this part of the range. Two of three distinctive features which characterize topography and relief in the study area can be directly related to their location inside the duplex array and are thus linked to interaction between eastern MFF and NTT, and between western MFF and Taleghan fault, respectively. To account for inferred inherited topography from the previous dextral-transpression regime, a new concept of tectonic landscape characterization has been used. Accordingly, I define simple landscapes as those environments, which have developed during the influence of a sustained tectonic regime. In contrast, composite landscapes contain topographic elements inherited from previous tectonic conditions that are inconsistent with the regional present-day stress field and kinematic style. Using numerical fault-interaction modeling with different tectonic boundary conditions, I calculated synoptic snapshots of artificial topography to compare it with the real topographic metrics. However, in the Alborz mountains, E-W faults are favorably oriented to accommodate the entire range of NW- to NE-directed compression. These faults show the highest total displacement which might indicate sustained faulting under changing boundary conditions. In contrast to the fault system within and at the flanks of the Alborz mountains, Quaternary deformation in the adjacent Tehran plain is characterized by oblique motion and thrust and strike-slip fault systems. In this morphotectonic province fault-propagation folding along major faults, limited strike-slip motion, and en-{\´e}chelon arrays of second-order upper plate thrusts are typical. While the Tehran plain is characterized by young deformation phenomena, the majority of faulting took place in the early stages of the Quaternary and during late Pliocene time. TCN-dating, which was performed for the first time on geomorphic surfaces in the Tehran plain, revealed that the oldest two phases of alluviation (units A and B) must be older than late Pleistocene. While urban development in Tehran increasingly covers and obliterates the active fault traces, the present-day kinematic style, the vestiges of formerly undeformed Quaternary landforms, and paleo earthquake indicators from the last millennia attest to the threat that these faults and their related structures pose for the megacity.},
  language  = {en}
}
@phdthesis{Borchers2010,
  author    = {Borchers, Andreas},
  title     = {Glaciomarine sedimentation at the continental margin of Prydz Bay, East Antarctica : implications on palaeoenvironmental changes during the Quaternary},
  url       = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus-52620},
  school      = {Universit{\"a}t Potsdam},
  year      = {2010},
  abstract  = {The Antarctic plays an important role in the global climate system. On the one hand, the Antarctic Ice Sheet is the largest freshwater reservoir on Earth. On the other hand, a major proportion of the global bottom-water formation takes place in Antarctic shelf regions, forcing the global thermohaline circulation. The main goal of this dissertation is to provide new insights into the dynamics and stability of the EAIS during the Quaternary. Additionally, variations in the activity of bottom-water formation and their causes are investigated. The dissertation is a German contribution to the International Polar Year 2007/ 2008 and was funded by the 'Deutsche Forschungsgesellschaft' (DFG) within the scope of priority program 1158 'Antarctic research with comparative studies in Arctic ice regions'. During RV Polarstern expedition ANT-XXIII/9, glaciomarine sediments were recovered from the Prydz Bay-Kerguelen region. Prydz Bay is a key region for the study of East EAIS dynamics, as 16\% of the EAIS are drained through the Lambert Glacier into the bay. Thereby, the glacier transports sediment into Prydz Bay which is then further distributed by calving icebergs or by current transport. The scientific approach of this dissertation is the reconstruction of past glaciomarine environments to infer on the response of the Lambert Glacier-Amery Ice Shelf system to climate shifts during the Quaternary. To characterize the depositional setting, sedimentological methods are used and statistical analyses are applied. Mineralogical and (bio)geochemical methods provide a means to reconstruct sediment provenances and to provide evidence on changes in the primary production in the surface water column. Age-depth models were constructed based on palaeomagnetic and palaeointensity measurements, diatom stratigraphy and radiocarbon dating. Sea-bed surface sediments in the investigation area show distinct variations in terms of their clay minerals and heavy-mineral assemblages. Considerable differences in the mineralogical composition of surface sediments are determined on the continental shelf. Clay minerals as well as heavy minerals provide useful parameters to differentiate between sediments which originated from erosion of crystalline rocks and sediments originating from Permo-Triassic deposits. Consequently, mineralogical parameters can be used to reconstruct the provenance of current-transported and ice-rafted material. The investigated sediment cores cover the time intervals of the last 1.4 Ma (continental slope) and the last 12.8 cal. ka BP (MacRobertson shelf). The sediment deposits were mainly influenced by glacial and oceanographic processes and further by biological activity (continental shelf), meltwater input and possibly gravitational transport. Sediments from the continental slope document two major deglacial events: the first deglaciation is associated with the mid-Pleistocene warming recognized around the Antarctic. In Prydz Bay, the Lambert Glacier-Amery Ice Shelf retreated far to the south and high biogenic productivity commenced or biogenic remains were better preserved due to increased sedimentation rates. Thereafter, stable glacial conditions continued until 400 - 500 ka BP. Calving of icebergs was restricted to the western part of the Lambert Glacier. The deeper bathymetry in this area allows for floating ice shelf even during times of decreased sea-level. Between 400 - 500 ka BP and the last interglacial (marine isotope stage 5) the glacier was more dynamic. During or shortly after the last interglacial the LAIS retreated again due to sea-level rise of 6 - 9 m. Both deglacial events correlate with a reduction in the thickness of ice masses in the Prince Charles Mountains. It indicates that a disintegration of the Amery Ice Shelf possibly led to increased drainage of ice masses from the Prydz Bay hinterland. A new end-member modelling algorithm was successfully applied on sediments from the MacRobertson shelf used to unmix the sand grain size fractions sorted by current activity and ice transport, respectively. Ice retreat on MacRobertson Shelf commenced 12.8 cal. ka BP and ended around 5.5 cal. ka BP. During the Holocene, strong fluctuations of the bottomwater activity were observed, probably related to variations of sea-ice formation in the Cape Darnley polynya. Increased activity of bottom-water flow was reconstructed at transitions from warm to cool conditions, whereas bottom-water activity receded during the mid- Holocene climate optimum. It can be concluded that the Lambert Glacier-Amery Ice Shelf system was relatively stable in terms of climate variations during the Quaternary. In contrast, bottom-water formation due to polynya activity was very sensitive to changes in atmospheric forcing and should gain more attention in future research.},
  language  = {en}
}
@phdthesis{Hoechner2010,
  author    = {H{\"o}chner, Andreas},
  title     = {GPS based analysis of earthquake induced phenomena at the Sunda Arc},
  url       = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus-53166},
  school      = {Universit{\"a}t Potsdam},
  year      = {2010},
  abstract  = {Indonesia is one of the countries most prone to natural hazards. Complex interaction of several tectonic plates with high relative velocities leads to approximately two earthquakes with magnitude Mw>7 every year, being more than 15\% of the events worldwide. Earthquakes with magnitude above 9 happen far more infrequently, but with catastrophic effects. The most severe consequences thereby arise from tsunamis triggered by these subduction-related earthquakes, as the Sumatra-Andaman event in 2004 showed. In order to enable efficient tsunami early warning, which includes the estimation of wave heights and arrival times, it is necessary to combine different types of real-time sensor data with numerical models of earthquake sources and tsunami propagation. This thesis was created as a result of the GITEWS project (German Indonesian Tsunami Early Warning System). It is based on five research papers and manuscripts. Main project-related task was the development of a database containing realistic earthquake scenarios for the Sunda Arc. This database provides initial conditions for tsunami propagation modeling used by the simulation system at the early warning center. An accurate discretization of the subduction geometry, consisting of 25x150 subfaults was constructed based on seismic data. Green's functions, representing the deformational response to unit dip- and strike slip at the subfaults, were computed using a layered half-space approach. Different scaling relations for earthquake dimensions and slip distribution were implemented. Another project-related task was the further development of the 'GPS-shield' concept. It consists of a constellation of near field GPS-receivers, which are shown to be very valuable for tsunami early warning. The major part of this thesis is related to the geophysical interpretation of GPS data. Coseismic surface displacements caused by the 2004 Sumatra earthquake are inverted for slip at the fault. The effect of different Earth layer models is tested, favoring continental structure. The possibility of splay faulting is considered and shown to be a secondary order effect in respect to tsunamigenity for this event. Tsunami models based on source inversions are compared to satellite radar altimetry observations. Postseismic GPS time series are used to test a wide parameter range of uni- and biviscous rheological models of the asthenosphere. Steady-state Maxwell rheology is shown to be incompatible with near-field GPS data, unless large afterslip, amounting to more than 10\% of the coseismic moment is assumed. In contrast, transient Burgers rheology is in agreement with data without the need for large aseismic afterslip. Comparison to postseismic geoid observation by the GRACE satellites reveals that even with afterslip, the model implementing Maxwell rheology results in amplitudes being too small, and thus supports a biviscous asthenosphere. A simple approach based on the assumption of quasi-static deformation propagation is introduced and proposed for inversion of coseismic near-field GPS time series. Application of this approach to observations from the 2004 Sumatra event fails to quantitatively reconstruct the rupture propagation, since a priori conditions are not fulfilled in this case. However, synthetic tests reveal the feasibility of such an approach for fast estimation of rupturing properties.},
  language  = {en}
}
@phdthesis{Guse2010,
  author    = {Guse, Bj{\"o}rn Felix},
  title     = {Improving flood frequency analysis by integration of empirical and probabilistic regional envelope curves},
  url       = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus-49265},
  school      = {Universit{\"a}t Potsdam},
  year      = {2010},
  abstract  = {Flood design necessitates discharge estimates for large recurrence intervals. However, in a flood frequency analysis, the uncertainty of discharge estimates increases with higher recurrence intervals, particularly due to the small number of available flood data. Furthermore, traditional distribution functions increase unlimitedly without consideration of an upper bound discharge. Hence, additional information needs to be considered which is representative for high recurrence intervals. Envelope curves which bound the maximum observed discharges of a region are an adequate regionalisation method to provide additional spatial information for the upper tail of a distribution function. Probabilistic regional envelope curves (PRECs) are an extension of the traditional empirical envelope curve approach, in which a recurrence interval is estimated for a regional envelope curve (REC). The REC is constructed for a homogeneous pooling group of sites. The estimation of this recurrence interval is based on the effective sample years of data considering the intersite dependence among all sites of the pooling group. The core idea of this thesis was an improvement of discharge estimates for high recurrence intervals by integrating empirical and probabilistic regional envelope curves into the flood frequency analysis. Therefore, the method of probabilistic regional envelope curves was investigated in detail. Several pooling groups were derived by modifying candidate sets of catchment descriptors and settings of two different pooling methods. These were used to construct PRECs. A sensitivity analysis shows the variability of discharges and the recurrence intervals for a given site due to the different assumptions. The unit flood of record which governs the intercept of PREC was determined as the most influential aspect. By separating the catchments into nested and unnested pairs, the calculation algorithm for the effective sample years of data was refined. In this way, the estimation of the recurrence intervals was improved, and therefore the use of different parameter sets for nested and unnested pairs of catchments is recommended. In the second part of this thesis, PRECs were introduced into a distribution function. Whereas in the traditional approach only discharge values are used, PRECs provide a discharge and its corresponding recurrence interval. Hence, a novel approach was developed, which allows a combination of the PREC results with the traditional systematic flood series while taking the PREC recurrence interval into consideration. An adequate mixed bounded distribution function was presented, which in addition to the PREC results also uses an upper bound discharge derived by an empirical envelope curve. By doing so, two types of additional information which are representative for the upper tail of a distribution function were included in the flood frequency analysis. The integration of both types of additional information leads to an improved discharge estimation for recurrence intervals between 100 and 1000 years.},
  language  = {en}
}