@article{ThiedeCabezaMishurovaetal.2018, author = {Thiede, Tobias and Cabeza, Sandra and Mishurova, Tatiana and Nadammal, Naresh and Kromm, Arne and Bode, Johannes and Haberland, Christoph and Bruno, Giovanni}, title = {Residual Stress in Selective Laser Melted Inconel 718}, series = {Materials performance and characterization}, volume = {7}, journal = {Materials performance and characterization}, number = {4}, publisher = {American Society for Testing and Materials}, address = {West Conshohocken}, issn = {2379-1365}, doi = {10.1520/MPC20170119}, pages = {717 -- 735}, year = {2018}, abstract = {The residual stress distribution in IN718 elongated prisms produced by selective laser melting was studied by means of neutron (bulk) and laboratory X-ray (surface) diffraction. Two deposition hatch lengths were considered. A horizontal plane near the top surface (perpendicular to the building direction) and a vertical plane near the lateral surface (parallel to the building direction) were investigated. Samples both in as-built (AB) condition and removed from the base plate (RE) were characterized. While surface stress fields seem constant for the AB condition, X-ray diffraction shows stress gradients along the hatch direction in the RE condition. The stress profiles correlate with the distortion maps obtained by tactile probe measurements. Neutron diffraction shows bulk stress gradients for all principal components along the main sample directions. We correlate the observed stress patterns with the hatch length, i.e., with its effect on temperature gradients and heat flow. The bulk stress gradients partially disappear after removal from the base plate.}, language = {en} } @article{StegemannCabezaPelkneretal.2018, author = {Stegemann, Robert and Cabeza, Sandra and Pelkner, Matthias and Lyamkin, Viktor and Pittner, Andreas and Werner, Daniel and Wimpory, Robert and Boin, Mirko and Kreutzbruck, Marc and Bruno, Giovanni}, title = {Influence of the microstructure on magnetic stray fields of low-carbon steel welds}, series = {Journal of Nondestructive Evaluation}, volume = {37}, journal = {Journal of Nondestructive Evaluation}, number = {3}, publisher = {Springer}, address = {New York}, issn = {0195-9298}, doi = {10.1007/s10921-018-0522-0}, pages = {18}, year = {2018}, abstract = {This study examines the relationship between the magnetic mesostructure with the microstructure of low carbon steel tungsten inert gas welds. Optical microscopy revealed variation in the microstructure of the parent material, in the heat affected and fusion zones, correlating with distinctive changes in the local magnetic stray fields measured with high spatial resolution giant magneto resistance sensors. In the vicinity of the heat affected zone high residual stresses were found using neutron diffraction. Notably, the gradients of von Mises stress and triaxial magnetic stray field modulus follow the same tendency transverse to the weld. In contrast, micro-X-ray fluorescence characterization indicated that local changes in element composition had no independent effect on magnetic stray fields.}, language = {en} } @article{NadammalCabezaMishurovaetal.2017, author = {Nadammal, Naresh and Cabeza, Sandra and Mishurova, Tatiana and Thiede, Tobias and Kromm, Arne and Seyfert, Christoph and Farahbod, Lena and Haberland, Christoph and Schneider, Judith Ann and Portella, Pedro Dolabella and Bruno, Giovanni}, title = {Effect of hatch length on the development of microstructure, texture and residual stresses in selective laser melted superalloy Inconel 718}, series = {Materials \& Design}, volume = {134}, journal = {Materials \& Design}, publisher = {Elsevier}, address = {Oxford}, issn = {0264-1275}, doi = {10.1016/j.matdes.2017.08.049}, pages = {139 -- 150}, year = {2017}, abstract = {In the present study, samples fabricated by varying the deposition hatch length during selective laser melting of nickel based superalloy Inconel 718 were investigated. Microstructure and texture of these samples was characterized using scanning electron microscopy, combined with electron back-scattered diffraction, and residual stress assessment, using neutron diffraction method. Textured columnar grains oriented along the sample building direction were observed in the shorter hatch length processed sample. A ten-fold increase in the hatch length reduced the texture intensity by a factor of two attributed to the formation of finer grains in the longer hatch length sample. Larger gradients of transverse residual stress in the longer hatch length sample were also observed. Along the build direction, compressive stresses in the shorter hatch length and negligible stresses for the longer hatch length specimen were observed. Changes to the temperature gradient (G) in response to the hatch length variation, influenced the G to growth rate (R) ratio and the product GxR, in agreement with the microstructures and textures formed. For the residual stress development, geometry of the part also played an important role. In summary, tailored isotropy could be induced in Inconel 718 by a careful selection of parameters during selective laser melting.}, language = {en} } @article{MishurovaStegemannLyamkinetal.2022, author = {Mishurova, Tatiana and Stegemann, Robert and Lyamkin, Viktor and Cabeza, Sandra and Evsevleev, Sergei and Pelkner, Matthias and Bruno, Giovanni}, title = {Subsurface and bulk residual stress analysis of S235JRC+C Steel TIG weld by diffraction and magnetic stray field measurements}, series = {Experimental mechanics : an international journal of the Society for Experimental Mechanics}, volume = {62}, journal = {Experimental mechanics : an international journal of the Society for Experimental Mechanics}, number = {6}, publisher = {Springer}, address = {New York}, issn = {0014-4851}, doi = {10.1007/s11340-022-00841-x}, pages = {1017 -- 1025}, year = {2022}, abstract = {Background Due to physical coupling between mechanical stress and magnetization in ferromagnetic materials, it is assumed in the literature that the distribution of the magnetic stray field corresponds to the internal (residual) stress of the specimen. The correlation is, however, not trivial, since the magnetic stray field is also influenced by the microstructure and the geometry of component. The understanding of the correlation between residual stress and magnetic stray field could help to evaluate the integrity of welded components. Objective This study aims at understanding the possible correlation of subsurface and bulk residual stress with magnetic stray field in a low carbon steel weld. Methods The residual stress was determined by synchrotron X-ray diffraction (SXRD, subsurface region) and by neutron diffraction (ND, bulk region). SXRD possesses a higher spatial resolution than ND. Magnetic stray fields were mapped by utilizing high-spatial-resolution giant magneto resistance (GMR) sensors. Results The subsurface residual stress overall correlates better with the magnetic stray field distribution than the bulk stress. This correlation is especially visible in the regions outside the heat affected zone, where the influence of the microstructural features is less pronounced but steep residual stress gradients are present. Conclusions It was demonstrated that the localized stray field sources without any obvious microstructural variations are associated with steep stress gradients. The good correlation between subsurface residual stress and magnetic signal indicates that the source of the magnetic stray fields is to be found in the range of the penetration depth of the SXRD measurements.}, language = {en} } @article{MishurovaCabezaThiedeetal.2018, author = {Mishurova, Tatiana and Cabeza, Sandra and Thiede, Tobias and Nadammal, Naresh and Kromm, Arne and Klaus, Manuela and Genzel, Christoph and Haberland, Christoph and Bruno, Giovanni}, title = {The Influence of the Support Structure on Residual Stress and Distortion in SLM Inconel 718 Parts}, series = {Metallurgical and Materials Transactions A}, volume = {49A}, journal = {Metallurgical and Materials Transactions A}, number = {7}, publisher = {Springer}, address = {New York}, issn = {1073-5623}, doi = {10.1007/s11661-018-4653-9}, pages = {3038 -- 3046}, year = {2018}, abstract = {The effect of support structure and of removal from the base plate on the residual stress state in selective laser melted IN718 parts was studied by means of synchrotron X-ray diffraction. The residual stresses in subsurface region of two elongated prisms in as-built condition and after removal from the base plate were determined. One sample was directly built on a base plate and another one on a support structure. Also, the distortion on the top surface due to stress release was measured by contact profilometry. High tensile residual stress values were found, with pronounced stress gradient along the hatching direction. In the sample on support, stress redistribution took place after removal from the base plate, as opposed to simple stress relaxation for the sample without support. The sample on support structure showed larger distortion compared to sample without support. We conclude that the use of a support decreases stress values but stress-relieving heat treatments are still needed.}, language = {en} } @article{MishurovaCabezaArtztetal.2017, author = {Mishurova, Tatiana and Cabeza, Sandra and Artzt, Katia and Haubrich, Jan and Klaus, Manuela and Genzel, Christoph and Requena, Guillermo and Bruno, Giovanni}, title = {An Assessment of Subsurface Residual Stress Analysis in SLM Ti-6Al-4V}, series = {Materials}, volume = {10}, journal = {Materials}, publisher = {MDPI}, address = {Basel}, issn = {1996-1944}, doi = {10.3390/ma10040348}, pages = {14}, year = {2017}, abstract = {Ti-6Al-4V bridges were additively fabricated by selective laser melting (SLM) under different scanning speed conditions, to compare the effect of process energy density on the residual stress state. Subsurface lattice strain characterization was conducted by means of synchrotron diffraction in energy dispersive mode. High tensile strain gradients were found at the frontal surface for samples in an as-built condition. The geometry of the samples promotes increasing strains towards the pillar of the bridges. We observed that the higher the laser energy density during fabrication, the lower the lattice strains. A relief of lattice strains takes place after heat treatment.}, language = {en} } @article{FernandezCabezaMishurovaetal.2018, author = {Fernandez, R. and Cabeza, Sandra and Mishurova, Tatiana and Fernandez-Castrillo, P. and Gonzalez-Doncel, Gaspar and Bruno, Giovanni}, title = {Residual stress and yield strength evolution with annealing treatments in an age-hardenable aluminum alloy matrix composite}, series = {Materials Science and Engineering: A}, volume = {731}, journal = {Materials Science and Engineering: A}, publisher = {Elsevier}, address = {Lausanne}, issn = {0921-5093}, doi = {10.1016/j.msea.2018.06.031}, pages = {344 -- 350}, year = {2018}, abstract = {We investigated the possibility of minimizing tensile matrix residual stresses in age hardenable aluminum alloy metal matrix composites without detrimentally affect their mechanical properties (such as yield strength). Specifically, we performed thermal treatments at different temperatures and times in an age-hardenable aluminum matrix composite 2014Al-15vol\%Al2O3. Using X-ray synchrotron radiation diffraction and mechanical tests, we show that below a certain treatment temperature (250 degrees C) it is possible to identify an appropriate thermal treatment capable of relaxing residual stress in this composite while even increasing its yield strength, with respect to the as processed conditions.}, language = {en} } @article{EvsevleevMishurovaCabezaetal.2018, author = {Evsevleev, Sergei and Mishurova, Tatiana and Cabeza, Sandra and Koos, R. and Sevostianov, Igor and Garc{\´e}s, Gonzales and Requena, Guillermo and Fernandez, R. and Bruno, Giovanni}, title = {The role of intermetallics in stress partitioning and damage evolution of AlSil2CuMgNi alloy}, series = {Materials Science and Engineering: A-Structural materials: properties, microstructure and processing}, volume = {736}, journal = {Materials Science and Engineering: A-Structural materials: properties, microstructure and processing}, publisher = {Elsevier}, address = {Lausanne}, issn = {0921-5093}, doi = {10.1016/j.msea.2018.08.070}, pages = {453 -- 464}, year = {2018}, abstract = {Load partitioning between phases in a cast AlSi12CuMgNi alloy was investigated by in-situ compression test during neutron diffraction experiments. Computed tomography (CT) was used to determine volume fractions of eutectic Si and intermetallic (IM) phases, and to assess internal damage after ex-situ compression tests. The CT reconstructed volumes showed the interconnectivity of IM phases, which build a 3D network together with eutectic Si. Large stresses were found in IMs, revealing their significant role as a reinforcement for the alloy. An existing micromechanical model based on Maxwell scheme was extended to the present case, assuming the alloy as a three-phase composite (Al matrix, eutectic Si, IM phases). The model agrees well with the experimental data. Moreover, it allows predicting the principal stresses in each phase, while experiments can only determine stress differences between the axial and radial sample directions. Finally, we showed that the addition of alloying elements not only allowed developing a 3D interconnected network, but also improved the strength of the Al matrix, and the ability of the alloy constituents to bear mechanical load.}, language = {en} } @article{CabezaMuellerPereyraetal.2018, author = {Cabeza, Sandra and M{\"u}ller, Bernd R. and Pereyra, Ricio and Fernandez, Ricardo and Gonzalez-Doncel, Gaspar and Bruno, Giovanni}, title = {Evidence of damage evolution during creep of Al-Mg alloy using synchrotron X-ray refraction}, series = {Journal of applied crystallography}, volume = {51}, journal = {Journal of applied crystallography}, publisher = {International Union of Crystallography}, address = {Chester}, issn = {1600-5767}, doi = {10.1107/S1600576718001449}, pages = {420 -- 427}, year = {2018}, abstract = {In order to provide further evidence of damage mechanisms predicted by the recent solid-state transformation creep (SSTC) model, direct observation of damage accumulation during creep of Al-3.85Mg was made using synchrotron X-ray refraction. X-ray refraction techniques detect the internal specific surface (i.e. surface per unit volume) on a length scale comparable to the specimen size, but with microscopic sensitivity. A significant rise in the internal specific surface with increasing creep time was observed, providing evidence for the creation of a fine grain substructure, as predicted by the SSTC model. This substructure was also observed by scanning electron microscopy.}, language = {en} } @article{CabezaMishurovaGarcesetal.2017, author = {Cabeza, Sandra and Mishurova, Tatiana and Garc{\´e}s, Gonzales and Sevostianov, Igor and Requena, Guillermo and Bruno, Giovanni}, title = {Stress-induced damage evolution in cast AlSi12CuMgNi alloy with one- and two-ceramic reinforcements}, series = {Journal of materials science}, volume = {52}, journal = {Journal of materials science}, publisher = {Springer}, address = {New York}, issn = {0022-2461}, doi = {10.1007/s10853-017-1182-7}, pages = {10198 -- 10216}, year = {2017}, abstract = {Two composites, consisting of an as-cast AlSi12CuMgNi alloy reinforced with 15 vol\% Al2O3 short fibres and with 7 vol\% Al2O3 short fibres + 15 vol\% SiC particles, were studied. Synchrotron computed tomography disclosed distribution, orientation, and volume fraction of the different phases. In-situ compression tests during neutron diffraction in direction parallel to the fibres plane revealed the load partition between phases. Internal damage (fragmentation) of the Si phase and Al2O3 fibres was directly observed in CT reconstructions. Significant debonding between Al matrix and SiC particles was also found. Finally, based on the Maxwell scheme, a micromechanical model was utilized for the new composite with two-ceramic reinforcements; it rationalizes the experimental data and predicts the evolution of all internal stress components in each phase.}, language = {en} }