@article{MachatschekHeuchelLendlein2021, author = {Machatschek, Rainhard Gabriel and Heuchel, Matthias and Lendlein, Andreas}, title = {Hydrolytic stability of polyetherimide investigated in ultrathin films}, series = {Journal of materials research : JMR / Materials Research Society}, volume = {36}, journal = {Journal of materials research : JMR / Materials Research Society}, number = {14}, publisher = {Springer}, address = {Berlin}, issn = {0884-2914}, doi = {10.1557/s43578-021-00267-6}, pages = {2987 -- 2994}, year = {2021}, abstract = {Increasing the surface hydrophilicity of polyetherimide (PEI) through partial hydrolysis of the imide groups while maintaining the length of the main-chain was explored for adjusting its function in biomedical and membrane applications. The outcome of the polymer analogous reaction, i.e., the degree of ring opening and chain cleavage, is difficult to address in bulk and microstructured systems, as these changes only occur at the interface. Here, the reaction was studied at the air-water interface using the Langmuir technique, assisted by atomic force microscopy and vibrational spectroscopy. Slow PEI hydrolysis sets in at pH > 12. At pH = 14, the ring opening is nearly instantaneous. Reduction of the layer viscosity with time at pH = 14 suggested moderate chain cleavage. No hydrolysis was observed at pH = 1. Hydrolyzed PEI films had a much more cohesive structure, suggesting that the nanoporous morphology of PEI can be tuned via hydrolysis.}, language = {en} } @article{MachatschekHeuchelLendlein2021, author = {Machatschek, Rainhard Gabriel and Heuchel, Matthias and Lendlein, Andreas}, title = {Thin-layer studies on surface functionalization of polyetherimide}, series = {Journal of materials research : JMR / Materials Research Society}, volume = {37}, journal = {Journal of materials research : JMR / Materials Research Society}, number = {1}, publisher = {Springer}, address = {Berlin}, issn = {0884-2914}, doi = {10.1557/s43578-021-00339-7}, pages = {67 -- 76}, year = {2021}, abstract = {Among the high-performance and engineering polymers, polyimides and the closely related polyetherimide (PEI) stand out by their capability to react with nucleophiles under relatively mild conditions. By targeting the phthalimide groups in the chain backbone, post-functionalization offers a pathway to adjust surface properties such as hydrophilicity, solvent resistance, and porosity. Here, we use ultrathin PEI films on a Langmuir trough as a model system to investigate the surface functionalization with ethylene diamine and tetrakis(4-aminophenyl)porphyrin as multivalent nucleophiles. By means of AFM, Raman spectroscopy, and interfacial rheology, we show that hydrolysis enhances the chemical and mechanical stability of ultrathin films and allows for the formation of EDC/NHS-activated esters. Direct amidation of PEI was achieved in the presence of a Lewis acid catalyst, resulting in free amine groups rather than cross-linking. When comparing amidation with hydrolysis, we find a greater influence of the latter on material properties.}, language = {en} } @article{SauterKratzHeucheletal.2021, author = {Sauter, Tilman and Kratz, Karl and Heuchel, Matthias and Lendlein, Andreas}, title = {Fiber diameter as design parameter for tailoring the macroscopic shape-memory performance of electrospun meshes}, series = {Materials and design}, volume = {202}, journal = {Materials and design}, publisher = {Elsevier}, address = {Amsterdam [u.a.]}, issn = {1873-4197}, doi = {10.1016/j.matdes.2021.109546}, pages = {10}, year = {2021}, abstract = {Fibrous shape-memory polymer (SMP) scaffolds were investigated considering the fiber as basic microstructural feature. By reduction of the fiber diameter in randomly oriented electrospun polyetherurethane (PEU) meshes from the micro-to the nano-scale, we observed changes in the molecular orientation within the fibers and its impact on the structural and shape-memory performance. It was assumed that a spatial restriction by reduction of the fiber diameter increases molecular orientation along the orientation of the fiber. The stress-strain relation of random PEU scaffolds is initially determined by the 3D arrangement of the fibers and thus is independent of the molecular orientation. Increasing the molecular orientation with decreasing single fiber diameter in scaffolds composed of randomly arranged fibers did not alter the initial stiffness and peak stress but strongly influenced the elongation at break and the stress increase above the Yield point. Reduction of the single fiber diameter also distinctly improved the shape-memory performance of the scaffolds. Fibers with nanoscale diameters (< 100 nm) possessed an almost complete shape recovery, high recovery stresses and fast relaxation kinetics, while the shape fixity was found to decrease with decreasing fiber diameter. Hence, the fiber diameter is a relevant design parameter for SMP.}, language = {en} } @article{LendleinHeuchel2021, author = {Lendlein, Andreas and Heuchel, Matthias}, title = {Shape-memory polymers designed in view of thermomechanical energy storage and conversion systems}, series = {ACS central science}, volume = {7}, journal = {ACS central science}, number = {10}, publisher = {American Chemical Society}, address = {Washington}, issn = {2374-7951}, doi = {10.1021/acscentsci.1c01032}, pages = {1599 -- 1601}, year = {2021}, language = {en} } @article{IzraylitHeuchelKratzetal.2021, author = {Izraylit, Victor and Heuchel, Matthias and Kratz, Karl and Lendlein, Andreas}, title = {Non-woven shape-memory polymer blend actuators}, series = {MRS advances : a journal of the Materials Research Society (MRS)}, volume = {6}, journal = {MRS advances : a journal of the Materials Research Society (MRS)}, number = {33}, publisher = {Springer Nature Switzerland AG}, address = {Cham}, issn = {2059-8521}, doi = {10.1557/s43580-021-00063-8}, pages = {781 -- 785}, year = {2021}, abstract = {The hierarchical design approach provides various opportunities to adjust the structural performance of polymer materials. Electrospinning processing techniques give access to molecular orientation as a design parameter, which we consider here in view of the shape-memory actuation performance. The aim of this work is to investigate how the reversible strain epsilon'(rev) can be affected by a morphology change from a bulk material to an electrospun mesh. epsilon'(rev) could be increased from 5.5 +/- 0.5\% to 15 +/- 1.8\% for a blend from a multiblock copolymer with poly(epsilon-caprolactone) (PCL) and poly(L-lactide) (PLLA) segments with oligo(D-lactide) (ODLA). This study demonstrates an effective design approach for enhancing soft actuator performance, which can be broadly applied in soft robotics and medicine.}, language = {en} } @article{KumarHeuchelKratzetal.2018, author = {Kumar, Reddi K. and Heuchel, Matthias and Kratz, Karl and Lendlein, Andreas and Jankowski, Joachim and Tetali, Sarada D.}, title = {Effects of extracts prepared from modified porous poly(ether imide) microparticulate absorbers on cytotoxicity, macrophage differentiation and proinflammatory behavior of human monocytic (THP-1) cells}, series = {Clinical hemorheology and microcirculation : blood flow and vessels}, volume = {69}, journal = {Clinical hemorheology and microcirculation : blood flow and vessels}, number = {1-2}, publisher = {IOS Press}, address = {Amsterdam}, issn = {1386-0291}, doi = {10.3233/CH-189112}, pages = {175 -- 185}, year = {2018}, abstract = {Remaining uremic toxins in the blood of chronic renal failure patients represent one central challenge in hemodialysis therapies. Highly porous poly(ether imide) (PEI) microparticles have been recently introduced as candidate absorber materials, which show a high absorption capacity for uremic toxins and allow hydrophilic surface modification suitable for minimization of serum protein absorption. In this work, the effects of extracts prepared from PEI microparticles modified by nucleophilic reaction with low molecular weight polyethylene imine (Pei) or potassium hydroxide (KOH), on human monocytic (THP-1) cells are studied. The obtained results suggested that the extracts of Pei and KOH modified PEI absorbers have no negative effect on THP-1 cell viability and do not initiate the critical differentiation towards macrophages. The extracts did not enhance transcript or protein levels of investigated proinflammatory markers in THP-1 cells, namely, TNF alpha, MCP1, IL6 and IL8. Based on these findings such modified PEI microparticles should be qualified for further pre-clinical evaluation i.e. in an in vivo animal experiment.}, language = {en} } @article{WangRazzaqRudolphetal.2018, author = {Wang, Li and Razzaq, Muhammad Yasar and Rudolph, Tobias and Heuchel, Matthias and N{\"o}chel, Ulrich and Mansfeld, Ulrich and Jiang, Yi and Gould, Oliver E. C. and Behl, Marc and Kratz, Karl and Lendlein, Andreas}, title = {Reprogrammable, magnetically controlled polymeric nanocomposite actuators}, series = {Material horizons}, volume = {5}, journal = {Material horizons}, number = {5}, publisher = {Royal Society of Chemistry}, address = {Cambridge}, issn = {2051-6347}, doi = {10.1039/c8mh00266e}, pages = {861 -- 867}, year = {2018}, abstract = {Soft robots and devices with the advanced capability to perform adaptive motions similar to that of human beings often have stimuli-sensitive polymeric materials as the key actuating component. The external signals triggering the smart polymers' actuations can be transmitted either via a direct physical connection between actuator and controlling unit (tethered) or remotely without a connecting wire. However, the vast majority of such polymeric actuator materials are limited to one specific type of motion as their geometrical information is chemically fixed. Here, we present magnetically driven nanocomposite actuators, which can be reversibly reprogrammed to different actuation geometries by a solely physical procedure. Our approach is based on nanocomposite materials comprising spatially segregated crystallizable actuation and geometry determining units. Upon exposure to a specific magnetic field strength the actuators' geometric memory is erased by the melting of the geometry determining units allowing the implementation of a new actuator shape. The actuation performance of the nanocomposites can be tuned and the technical significance was demonstrated in a multi-cyclic experiment with several hundreds of repetitive free-standing shape shifts without losing performance.}, language = {en} } @article{RazzaqBehlHeucheletal.2019, author = {Razzaq, Muhammad Yasar and Behl, Marc and Heuchel, Matthias and Lendlein, Andreas}, title = {Matching magnetic heating and thermal actuation for sequential coupling in hybrid composites by design}, series = {Macromolecular rapid communications}, volume = {41}, journal = {Macromolecular rapid communications}, number = {1}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {1022-1336}, doi = {10.1002/marc.201900440}, pages = {7}, year = {2019}, abstract = {Sequentially coupling two material functions requires matching the output from the first with the input of the second function. Here, magnetic heating controls thermal actuation of a hybrid composite in a challenging system environment causing an elevated level of heat loss. The concept is a hierarchical design consisting of an inner actuator of nanocomposite material, which can be remotely heated by exposure to an alternating magnetic field (AMF) and outer layers of a porous composite system with a closed pore morphology. These porous layers act as heat insulators and as barriers to the surrounding water. By exposure to the AMF, a local bulk temperature of 71 degrees C enables the magnetic actuation of the device, while the temperature of the surrounding water is kept below 50 degrees C. Interestingly, the heat loss during magnetic heating leads to an increase of the water phase (small volume) temperature. The temperature increase is able to sequentially trigger an adjacent thermal actuator attached to the actuator composite. In this way it could be demonstrated how the AMF is able to initiate two kinds of independent actuations, which might be interesting for robotics operating in aqueous environments.}, language = {en} } @article{GhobadiHeuchelKratzetal.2014, author = {Ghobadi, Ehsan and Heuchel, Matthias and Kratz, Karl and Lendlein, Andreas}, title = {Atomistic simulation of the shape-memory effect in dry and water swollen Poly[(rac-lactide)-co-glycolide] and copolyester urethanes thereof}, series = {Macromolecular chemistry and physics}, volume = {215}, journal = {Macromolecular chemistry and physics}, number = {1}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {1022-1352}, doi = {10.1002/macp.201300507}, pages = {65 -- 75}, year = {2014}, abstract = {An atomistic molecular dynamics simulation approach is applied to model the influence of urethane linker units as well as the addition of water molecules on the simulated shape-memory properties of poly[(rac-lactide)-co-glycolide] (PLGA) and PLGA-based copolyester urethanes comprising different urethane linkers. The shape-memory performance of these amorphous packing models is explored in a simulated heating-deformation-cooling-heating procedure. Depending on the type of incorporated urethane linker, the mechanical properties of the dry copolyester urethanes are found to be significantly improved compared with PLGA, which can be attributed to the number of intermolecular hydrogen bonds between the urethane units. Good shape-memory properties are observed for all the modeled systems. In the dry state, the shape fixation is found to be improved by implementation of urethane units. After swelling of the copolymer models with water, which results in a reduction of their glass transition temperatures, the relaxation kinetics during unloading and shape recovery are found to be substantially accelerated.}, language = {en} } @article{GhobadiHeuchelKratzetal.2012, author = {Ghobadi, Ehsan and Heuchel, Matthias and Kratz, Karl and Lendlein, Andreas}, title = {Simulation of volumetric swelling of degradable poly[(rac-lactide)-co-glycolide] based polyesterurethanes containing different urethane-linkers}, series = {Journal of applied biomaterials \& functional materials}, volume = {10}, journal = {Journal of applied biomaterials \& functional materials}, number = {3}, publisher = {Wichtig}, address = {Milano}, issn = {2280-8000}, doi = {10.5301/JABFM.2012.10432}, pages = {293 -- 301}, year = {2012}, abstract = {Aim: The hydrolytic degradation behavior of degradable aliphatic polyester-based polymers is strongly influenced by the uptake or transport of water into the polymer matrix and also the hydrolysis rate of ester bonds. Methods: We examined the volumetric swelling behavior of poly[(rac-lactide)-co-glycolide] (PLGA) and PLGA-based polyurethanes (PLGA-PU) with water contents of 0 wt\%, 2 wt\% and 7 wt\% water at 310 K using a molecular modeling approach. Polymer systems with a number average molecular weight of M-n = 10,126 g.mol(-1) were constructed from PLGA with a lactide content of 67 mol\%, whereby PLGA-PU systems were composed of five PLGA segments with M-n = 2052 g.mol(-1), which were connected via urethane linkers originated from 2,2,4-trimethyl hexamethylene-1,6-diisocyanate (TMDI), hexamethyl-1,6-diisocyanate (HDI), or L-lysine-1,6-diisocyanate (LDI). Results: The calculated densities of the dry PLGA-PU systems were found to be lower than for pure PLGA. The obtained volumetric swelling of the PLGA-PU was depending on the type of urethane linker, whereby all swollen PLGA-PUs contained larger free volume distribution compared to pure PLGA. The mean square displacement curves for dry PLGA and PLGA-PUs showed that urethane linker units reduce the mobility of the polymer chains, while an increase in backbone atoms mobility was found, when water was added to these systems. Consequently, an increased water uptake of PLGA-PU matrices combined with a higher mobility of the chain segments should result in an accelerated hydrolytic chain scission rate in comparison to PLGA. Conclusions: It can be anticipated that the incorporation of urethane linkers might be a helpful tool to adjust the degradation behavior of polyesters.}, language = {en} }