@article{FandrichBullerSchaeferetal.2015,
  author    = {Fandrich, Artur and Buller, Jens and Sch{\"a}fer, Daniel and Wischerhoff, Erik and Laschewsky, Andr{\´e} and Lisdat, Fred},
  title     = {Electrochemical characterization of a responsive macromolecular interface on gold},
  series = {Physica status solidi : A, Applications and materials science},
  volume    = {212},
  journal   = {Physica status solidi : A, Applications and materials science},
  number    = {6},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1862-6300},
  doi       = {10.1002/pssa.201431698},
  pages     = {1359 -- 1367},
  year      = {2015},
  abstract  = {This study reports on the investigation of a thermoresponsive polymer as a thin film on electrodes and the influence of coupling a peptide and an antibody to the film. The utilized polymer from the class of poly(oligoethylene glycol)-methacrylate polymers (poly(OEGMA)) with carboxy functions containing side chains was synthesized and properly characterized in aqueous solutions. The dependence of the cloud point on the pH of the surrounding media is discussed. The responsive polymer was immobilized on gold electrodes as shown by electrochemical, quartz crystal microbalance (QCM), and atomic force microscopy (AFM) techniques. The temperature dependent behavior of the polymer covalently grafted to gold substrates is investigated using cyclic voltammetry (CV) in ferro-/ferricyanide solution. Significant changes in the slope of the temperature-dependence of the voltammetric peak current and the peak separation values clearly indicate the thermally induced conformational change on the surface. Finally, a biorecognition reaction between a short FLAG peptide (N-Asp-Tyr-Lys-Asp-Asp-Asp-Asp-Lys-C) covalently immobilized on the polymer interface and the corresponding IgG antibody was performed. The study shows that the responsiveness of the electrode is retained after peptide coupling and antibody binding, although the response is diminished.},
  language  = {en}
}
@article{FribergKovachKoetz2013,
  author    = {Friberg, Stig E. and Kovach, Ildiko and Koetz, Joachim},
  title     = {Equilibrium topology and partial inversion of Janus Drops - a numerical analysis},
  series = {ChemPhysChem : a European journal of chemical physics and physical chemistry},
  volume    = {14},
  journal   = {ChemPhysChem : a European journal of chemical physics and physical chemistry},
  number    = {16},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1439-4235},
  doi       = {10.1002/cphc.201300635},
  pages     = {3772 -- 3776},
  year      = {2013},
  abstract  = {The equilibrium topology of an aqueous Janus emulsion of two oils, O1 and O2, with water, W, [(O1+O2)/W], is numerically evaluated with the following realistic interfacial tensions (): (O2/W)=5 mNm(-1), (O1/O2)=1 mNm(-1), and (O1/W) varies within the range 4-5 mNm(-1), which is the limiting range for stable Janus drop topology. The relative significance of the two independently pivotal factors for the topology is evaluated, that is, the local equilibrium at the line of contact between the three liquids and the volume fraction of the two dispersed liquids within the drop. The results reveal a dominant effect of the local equilibrium on the fraction of the O2 drop surface that is covered by O1. In contrast, for a constant volume of O2, the impact of the interfacial tension balance on the limit of the coverage is modest for an infinite volume of O1. Interestingly, when the O1 volume exceeds this value, an emulsion inversion occurs, and the O1 portion of the (O1+O2)/W topology becomes a continuous phase, generating a (W+O2)/O1 Janus configuration.},
  language  = {en}
}