@article{AlbrechtSchaeferLangeetal.2012, author = {Albrecht, Steve and Schaefer, Sebastian and Lange, Ilja and Yilmaz, Seyfullah and Dumsch, Ines and Allard, Sybille and Scherf, Ullrich and Hertwig, Andreas and Neher, Dieter}, title = {Light management in PCPDTBT:PC70BM solar cells: A comparison of standard and inverted device structures}, series = {Organic electronics : physics, materials and applications}, volume = {13}, journal = {Organic electronics : physics, materials and applications}, number = {4}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1566-1199}, doi = {10.1016/j.orgel.2011.12.019}, pages = {615 -- 622}, year = {2012}, abstract = {We compare standard and inverted bulk heterojunction solar cells composed of PCPDTBT:PC70BM blends. Inverted devices comprising 100 nm thick active layers exhibited short circuit currents of 15 mA/cm(2), 10\% larger than in corresponding standard devices. Modeling of the optical field distribution in the different device stacks proved that this enhancement originates from an increased absorption of incident light in the active layer. Internal quantum efficiencies (IQEs) were obtained from the direct comparison of experimentally derived and modeled currents for different layer thicknesses, yielding IQEs of similar to 70\% for a layer thickness of 100 nm. Simulations predict a significant increase of the light harvesting efficiency upon increasing the layer thickness to 270 nm. However, a continuous deterioration of the photovoltaic properties with layer thickness was measured for both device architectures, attributed to incomplete charge extraction. On the other hand, our optical modeling suggests that inverted devices based on PCPDTBT should be able to deliver high power conversion efficiencies (PCEs) of more than 7\% provided that recombination losses can be reduced.}, language = {en} } @misc{MouleNeherTurner2014, author = {Moule, Adam J. and Neher, Dieter and Turner, Sarah T.}, title = {P3HT-Based solar cells: structural properties and photovoltaic performance}, series = {Advances in Polymer Science}, volume = {265}, journal = {Advances in Polymer Science}, editor = {Ludwigs, S}, publisher = {Springer}, address = {Berlin}, isbn = {978-3-662-45145-8; 978-3-662-45144-1}, issn = {0065-3195}, doi = {10.1007/12_2014_289}, pages = {181 -- 232}, year = {2014}, abstract = {Each year we are bombarded with B.Sc. and Ph.D. applications from students that want to improve the world. They have learned that their future depends on changing the type of fuel we use and that solar energy is our future. The hope and energy of these young people will transform future energy technologies, but it will not happen quickly. Organic photovoltaic devices are easy to sketch, but the materials, processing steps, and ways of measuring the properties of the materials are very complicated. It is not trivial to make a systematic measurement that will change the way other research groups think or practice. In approaching this chapter, we thought about what a new researcher would need to know about organic photovoltaic devices and materials in order to have a good start in the subject. Then, we simplified that to focus on what a new researcher would need to know about poly-3-hexylthiophene: phenyl-C61-butyric acid methyl ester blends (P3HT: PCBM) to make research progress with these materials. This chapter is by no means authoritative or a compendium of all things on P3HT: PCBM. We have selected to explain how the sample fabrication techniques lead to control of morphology and structural features and how these morphological features have specific optical and electronic consequences for organic photovoltaic device applications.}, language = {en} } @article{AlbrechtGrootoonkNeubertetal.2014, author = {Albrecht, Steve and Grootoonk, Bjorn and Neubert, Sebastian and Roland, Steffen and Wordenweber, Jan and Meier, Matthias and Schlatmann, Rutger and Gordijn, Aad and Neher, Dieter}, title = {Efficient hybrid inorganic/organic tandem solar cells with tailored recombination contacts}, series = {Solar energy materials \& solar cells : an international journal devoted to photovoltaic, photothermal, and photochemical solar energy conversion}, volume = {127}, journal = {Solar energy materials \& solar cells : an international journal devoted to photovoltaic, photothermal, and photochemical solar energy conversion}, publisher = {Elsevier}, address = {Amsterdam}, issn = {0927-0248}, doi = {10.1016/j.solmat.2014.04.020}, pages = {157 -- 162}, year = {2014}, abstract = {In this work, the authors present a 7.5\% efficient hybrid tandem solar cell with the bottom cell made of amorphous silicon and a Si-PCPDTBT:PC70BM bulk heterojunction top cell. Loss-free recombination contacts were realized by combing Al-doped ZnO with either the conducting polymer composite PEDOT:PSS or with a bilayer of ultrathin Al and MoO3. Optimization of these contacts results in tandem cells with high fill factors of 70\% and an open circuit voltage close to the sum of those of the sub-cells. This is the best efficiency reported for this type of hybrid tandem cell so far. Optical and electrical device modeling suggests that the efficiency can be increased to similar to 12\% on combining a donor polymer with suitable absorption onset with PCBM. We also describe proof-of-principle studies employing light trapping in hybrid tandem solar cells, suggesting that this device architecture has the potential to achieve efficiencies well above 12\%. (C) 2014 Elsevier B.V. All rights reserved.}, language = {en} } @misc{LaquaiAndrienkoDeibeletal.2017, author = {Laquai, Frederic and Andrienko, Denis and Deibel, Carsten and Neher, Dieter}, title = {Charge carrier generation, recombination, and extraction in polymer-fullerene bulk heterojunction organic solar cells}, series = {Elementary processes in organic photovoltaics}, volume = {272}, journal = {Elementary processes in organic photovoltaics}, publisher = {Springer}, address = {Berlin}, isbn = {978-3-319-28338-8}, issn = {0065-3195}, doi = {10.1007/978-3-319-28338-8_11}, pages = {267 -- 291}, year = {2017}, abstract = {In this chapter we review the basic principles of photocurrent generation in bulk heterojunction organic solar cells, discuss the loss channels limiting their efficiency, and present case studies of several polymer-fullerene blends. Using steady-state and transient, optical, and electrooptical techniques, we create a precise picture of the fundamental processes that ultimately govern solar cell efficiency.}, language = {en} } @phdthesis{Hosseini2022, author = {Hosseini, Seyed Mehrdad}, title = {Non-Langevin Recombination in Fullerene and Non-Fullerene Acceptor Solar Cells}, doi = {10.25932/publishup-54783}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-547831}, school = {Universit{\"a}t Potsdam}, pages = {XII, 103}, year = {2022}, abstract = {Organic solar cells (OSCs), in recent years, have shown high efficiencies through the development of novel non-fullerene acceptors (NFAs). Fullerene derivatives have been the centerpiece of the accepting materials used throughout organic photovoltaic (OPV) research. However, since 2015 novel NFAs have been a game-changer and have overtaken fullerenes. However, the current understanding of the properties of NFAs for OPV is still relatively limited and critical mechanisms defining the performance of OPVs are still topics of debate. In this thesis, attention is paid to understanding reduced-Langevin recombination with respect to the device physics properties of fullerene and non-fullerene systems. The work is comprised of four closely linked studies. The first is a detailed exploration of the fill factor (FF) expressed in terms of transport and recombination properties in a comparison of fullerene and non-fullerene acceptors. We investigated the key reason behind the reduced FF in the NFA (ITIC-based) devices which is faster non-geminate recombination relative to the fullerene (PCBM[70]-based) devices. This is then followed by a consideration of a newly synthesized NFA Y-series derivative which exhibits the highest power conversion efficiency for OSC at the time. Such that in the second study, we illustrated the role of disorder on the non-geminate recombination and charge extraction of thick NFA (Y6-based) devices. As a result, we enhanced the FF of thick PM6:Y6 by reducing the disorder which leads to suppressing the non-geminate recombination toward non-Langevin system. In the third work, we revealed the reason behind thickness independence of the short circuit current of PM6:Y6 devices, caused by the extraordinarily long diffusion length of Y6. The fourth study entails a broad comparison of a selection of fullerene and non-fullerene blends with respect to charge generation efficiency and recombination to unveil the importance of efficient charge generation for achieving reduced recombination. I employed transient measurements such as Time Delayed Collection Field (TDCF), Resistance dependent Photovoltage (RPV), and steady-state techniques such as Bias Assisted Charge Extraction (BACE), Temperature-Dependent Space Charge Limited Current (T-SCLC), Capacitance-Voltage (CV), and Photo-Induce Absorption (PIA), to analyze the OSCs. The outcomes in this thesis together draw a complex picture of multiple factors that affect reduced-Langevin recombination and thereby the FF and overall performance. This provides a suitable platform for identifying important parameters when designing new blend systems. As a result, we succeeded to improve the overall performance through enhancing the FF of thick NFA device by adjustment of the amount of the solvent additive in the active blend solution. It also highlights potentially critical gaps in the current experimental understanding of fundamental charge interaction and recombination dynamics.}, language = {en} }